valve

Hi All, 2010 FX 450, about 30 hrs. on it. I washed the bike and started her up, and now hear a new valve tapping noise that I have never heard before. The wash could be a coincidence. However, I saw this post in a Valve Adjustment thread: Re: 70 degree valve check/adjustment by Noppy »...

Hi guys Can somebody tell me correct valve clearances on my fe501 2003 been told not to go by the ones in manual Cheers

Hey guys im new to this site, and i have searched for valve adjustment and found a good post but it didnt work for me:P I know i have to get the piston at top before i can adjust them, i put the bike in 6th gear and turned the wheel to the piston was at top and the norwegian husaberg dealer...

Can anyone help me with what the valve clearences should be on my supermoto FE 550 , registered 09, but most likely built before that .

Hi there im about to put my beloved bike for sale . I want to check the valves before i sell it and i have no idea what how many mm clearance there is supose to be . Is there anyone who know the the clerance? My english isent that good so bear with me :) Thanks for the help

Hello guys. I'm looking to tune my TE 250 to the stock positions, but can't find the correct exhaust valve spring screw measure... That screw in the centre of the piece que remove to change the exhaust valve spring. I bought my bike with that screw about 2-3 turns out from flush... (flush...

Hi, After putting about 40 hrs on my Fe570s I decided to check my valves. Never done that before... It's about 35 degres F here and I'm getting about .004 on all my valves. I know that I'm out of specs. But is it due to cold temp? Thanks! Duane

Hi, I was hoping someone would walk me through how to adjust the valves on a 650. It is having a bit of a ticking sound when fully warmed(typical valve sound i guess). I am specifically interested in the "TURNing" method, since it seems to me that it's hard to get an accurate measurement ,cause...

I just bought an 08 fe450. The valves were checked 30 hours ago. When should I check the valves again and how often should I do it. Thanks

Several months ago I posted about my 98 FE400e locking up with a THUNK. I haven't had the time to dive into it until this past weekend. Here's what I found: One of the intake valve adjustment bolts broke. I found the end that pushes the valve, but the bolt is just plain gone. I've pulled...

Does anyone know the differences between valve guides 2004 and 2008 ? Looks like the valves are the same. 2004 part #59036025044 & 59036026044 update part numbers (superseded by Part# 59036025100 & 59036026100 ) 2008 part numbers 59036026101 & 59036025101

G'day again, Just a few questions regarding valve clearance adjustment on a Husaberg fs650e. 1. Are both intake and exhaust the same clearance......using the 1/6 turn?......because every other vehicle I've had the intake and exhaust are different measurements? 2. Can I set the intake valve...

Looking to do a oversize valves for my 2004 FS650 looking doing 36/31 vs stock of 35/30 any thoughts. The kebble whites valve are for a ktm 450 oversize black diamond stainless steel , anyone tried this combo????

Hi guys, not very mechanical here, but just finished my first valve adjust on my 08 fe450 today. had a shop do them last time, and while i watched, being alone is another story :) I went with 1/6 method The adjust itself is easy enough, but the issue is finding TDC. I tried to follow the...

Ok I have taken apart my kickstart mechanism to apply some upgrades, transmission cover off, clutch of. therefore no connection between primary drive gear and the balancer drive gear. Removed the valve cover in order to inspect the auto decomp ande valve springs etc. Turned the engine and...

I've been needing valve seals for my 98 501, and the suppliers I knew of were backordered. It's the only thing my bike has been needing, so I dug into it. My local KTM shop said that LC4 engines use VW Scirocco valve springs, so it got me wondering... I cross referenced the PN on my valve...

Hello fellow Berg owners! I am new to your forum and firstly thankyou for the wealth of information already contained here - it has saved me asking MANY questions! I am new to moto and have picked up a '09 FE450 w/ 22hrs. I now have 38.8hrs on her and decided to check the valve clearances. No...

Hello everyone, Hope you're all in good health! I have a 2000 501 FE. A few days ago I decided it was time to adjust the valves and so I did. Anyway, before I played with the valves the bike will start first or second kick, no problem, and will take a few attempts before it would start using...

01 fe650 I'm still trying to get it to start on the button....it did before. It seems the engine comes up to compression and stops dead, the starter can't turn it over. I've checked valves all is well. I decided to put a dial indicator on the exhaust valve to see if I was getting any movement on...

I have 2 2005 FE650s. One has 160hrs, cam chain replaced at 117hrs. The other one has 70hrs. Both run great and the valves are in spec at 1/6 turn out. I have noticed lately that the valve train and tappets are more noisy on the 160hr bike. Is there a wear item I should be looking into with...