valve

Hi guys. Just checked my clearances on a 2012 FE390 @ 115hrs. Both intakes are in middle of spec at 0.13mm (0.10 - 0.15 spec). Exhaust valve on cam chain side is at 0.15mm and exhaust valve on header side is at 0.20!! (0.12 - 0.17 spec). Should I change the shim on the exhaust at 0.20? It is...

My apologies but I couldn't find definitive info from a quick search. Anyone have luck removed the valve springs on an 08 Fe450 without taking the head off? Is there a special tool for this? Looking to change out valve seals and have tried a conventional overhead valve spring tool but...

2006 FE550. Time to check the valves. Does anyone know the actual clearances for the intake and exaust valves? I know about the 1/6 turn thing, I just have a hard time believing that the intake an exaust operate at the same temperature. Mabe I'm wrong. Someone please enlighten me. Thanks

Hi, I'm trying to find out what my valve clearances should be set at. I've got the pre 2000 manual from the manuals section but I'm not sure if its relevant to all pre 2000 as it says "1999 and pre 2000". Would all pre 2000 Berg's have the same clearances? Can anyone tell me what my...

Hey I'm new to this forum just wondering if someone could help me out finding a valve tappet screw for my 2000 fe 400. Ive been looking online everywhere and haven't found anything. I was wondering if there is a good substitute for this part or a good place to find them. Thanks

I've had a couple of hundred made by kibblewhite and they should be in stock in the next 2 weeks if the Customs don't knab them at the border for customs! they flow better than the OEM part otherwise they still use a clip and are made of unobtanium as ususal. regards Taffy

Today I saw that "hole" in my valve cover. Last time it was not there. It looks like it has been eaten by a chain? But the cam chain is tight even without tensioner. Has anyone seen something like that?

Just checked the valves on my 390 today. To my shame I realised I'd not checked them for about 160 hours. To the bikes credit, they were all still in spec with both inlets at 0.12mm and both exhausts at 0.15mm. Bike's now on 304 hours and 7807 miles. Whilst looking for the valve clearances...

What is the best way to lap valves? Has anyone used this Zim hand crank valve grinder (lapper)? Valve Tools

What is a good valve spring compressor for Husabergs? Has anyone used the Pit Posse tool? Would it work? Posse Valve Spring Compressor •Heavy-duty construction, economical priced •Comes with 16mm, 19mm, 23mm, 25mm, 30mm collars •Carrying case included •Max. opening...

:):)

Hello, so i'm rebuilding a husaberg fe 550 e 2008 some piscture how i make tearing down complete bike sandblaster frame with new coating and new plastics custom design graphics my cylinder head for a litle more power and flow :devil: 3 angle valve seat 30 / 45 /...

Dear fellow Berg`ers. Does anyone know the open/close valve data of the FS650, 2008? Thank you:D

Problem after problem when I order parts for my 2001 fx650 I rushed all over the country to gather all the maintenance parts I needed, then when I start the job I realize that my head has been modded and it requires 32mm exhaust valves. Yes, I should have striped the head and measured...

Hi all, Does anybody know if I can install a Husa part number 590.36.031.000 exhaust valve in a 2001 Husa FX650? KTm has them on the shelf locally, Husa OEM part number for my machine is 20000801 and they tell me not till end of summer delivery? thanks

Ok guys, the Husaberg mysteries keep my buddies laughing every weekend! We have seen MANY MANY 4 strokes needing clearance adjustment because the clearance gets reduced, Except for the mighty 2001 husa FX650, I actually keep gaining clearance on the exhaust valve. I have read some old...

Well guys, As usual I am looking for parts for my old Berg. I have done surprisingly well. Many shops told me I would not find any parts and others either had the parts or had the generic fix. I am now down to my last bit of items. The hardest one in the 4 valve guide seals for my 1991 fc501...

Having problems finding this info :-( I have 2 questions: 1- Does anybody know the free length (spec) for the valve springs on the 1991 fc501? 2- Does anyone know the part numbers and/or where to buy OEM or upgraded valve springs for this motor? Thanks, Jason

Hi. I checked my valves today , Valves measured at 6 Degrees C :inlet 0,07mm. exhaust : 0,09mm. I know they should be measured at 20 degrees C, but is this okey considering the temperature? Or will the clerance be less if the temperature is 20 degress?

I've tried search, but did not come with a definitive answer, so here I go. `10 FE390, around 190 hours, just acquired recently, don't know if valves were checked before, this is my first check, measured values are: (IN should be between 0.10 - 0.15mm) IN#1: between 0.13 - 0.15mm (ok) IN#2...