timing

i am not very up on husabergs...i have a 03 501fe...is the ignition timing adjustable on this bike...if so what is the correct timing for this....i downloaded the manual but the photos are blurry..or maybe a quick rundown would help more...thanx

I search on forum but cant find the answer , i don't know how adjusting ignition timing in my berg ,just read owners doc but i have different SEM stator :/ Sebastian

I am scheduled to pickup a new 570 Burg tuesday, now that I hear about the timing chain adjuster problem I am wondering if I should bail on the deal. During the summer I will be living about 300 miles from the nearest Burg dealer, and I sure don't want to spend my whole summer taking the Burg...

Is there anyone but me who has trouble with the hydraulic timing chain tensioner?It worked fine for a couple of hours but then it started to rattle at idle and low revs with the engine warmed up.Replaced it with a new tensioner but after only a couple of hours it´s the same story again.This...

Hi all after putting the head back to gather with the Taffy spring kit ( awesome kit by the way )and then timing the cam as per the 05 manual , line up the 3 dots on the primary pinion and the idler shaft gear then making sure the dots on the cam wheel are aliened with the edge of the head cam...

hi all got my old 92 fe 350 back the stator bolts came loose and the bike quit running i was able to repair the wires i think i got them good enough. But how do you set the timing. I see marks on the stator but won't be able to see them once the flywheel is on.

I need to ask a favor, I am doing some engine maintainance on my 07 Fe550. I am replacing the cam chain and need a rivet tool to install a new one. My closest dealer is 4 hours away and told me he won't lend his out. Does anyone have a suitable tool I could borrow? Of course I'll pay...

Looking thru the inspection hole in the timing cover if I move the mark on the stator to the right does this advance or retard the timing? What causes the timing marks on the flywheel to jump around when checking the timing at idle?

There are two marks on my flywheel one on the left and one to the right, what do these line up with when you are at TDC.I cannot find a mark on the flywheel cover, is there a mark somewhere else.

I am a new-be so here goes guys. I put a 2001 600cc motor in my 1993 FE 350 bike. the guy that sold me the motor put my 350 flywheel and ing on the 600 motor. My question is what is the proper timing spec for this combination. on the old 350 motor it say rotate the stater all the way to the...

a friend just traded for 07 450 and it sounded like a thrashing machine. everyone kept saying husaberg sounds like that, but seemed to me to be getting louder from clutch cover side. i had a 03 ktm 525 once sound like that and intermediate shaft nut came loose and sounded just like this husaberg...

Hi All i'm sure this has been covered before but can't find a thread, looking to set the timing on my 02 fs650e with a standard strobe light and wondered if one of you guys could tell me how many degrees advanced the line i should be marking to set this up and what revs this should be done at...

YAY i have now got my bike back together. I decided to replace the timing chain as i felt it was worn. It had the IWIS split chain, now it has a DID chain. While it was all apart i got hold of a water pump seal kit from Orange Berg. I would have to say this is one of the easiest and simple...

hi there , ive just bought a new stator coil for my 2002 fe400 but the new1 doesent have the resin type stuff on it so i dont have a timing mark so how do i find out if the timing is correct if i dont have the line to line it up with ?

Just confirming that if i removed the clutch basket, and during some moments of inepttitude, happened to move the timing gear (but did not remove the camchain) that all i have to do is line up the marks as identified in the image above and my timing should be back to normal correct?

Hi can anybody tell me if a timing chain from a 610 husky is the same pitch etc as a 400 fe husaberg as i got a new one for a husky but not a husaberg it looks the same and i can adjust the length is there any little fitting tricks i could be made aware of cheers all

I hate to sound to seriously brain dead but I have a large question. How can you check or adjust the timing on a 96 FE501? Give me a good answer and I will be happy to go back to my pints and then will adjust it. Preferably the more detailed the better. Thanks and take care.

Hey everyone! I am new to the forum everything looks great. Got a question for you guys. How do you set the cam timing on these babies? NO cam marks, whats the trick? please refesh my memory... Thank you in Advance

Whilst my bike is partially stripped-down I plan to check the camchain tension, valve clearances and timing. What order should this be done in? 1) Check camchain tension? 2) Set Valve clearances? 3) Check ignition timing? Does it matter? I don't think my camchain tensioner spring is strong...

Hi, I´m looking for the correct Throttle valve height Couldn´t find any info :( in the owner-,workshop- or parts-manual & owner doc ... Carb is a Keihin FCR 41 , Bike a FE550/07 Can anybody help?