timing

I,ve just replaced the stator on a 02 650. The right bearing had gone and wiped out the stator etc. There are two marks on the flywheel can someone tell me which one I need to line up with the stator to correctly set the ignition. The pictures on the manual are not clear enough to show this...

How do the marks line up on the cam sprocket( 1 mark ) crankshaft sprocket ( 2 marks) on a 03' 650 I'm in the process of putting motor back and I can't remember how they were aligned. :x I believe cam sprocket mark is to be @ 6:00 in between the 2 marks on crankshaft spocket @ 12:00 position...

any body know about the timing on the fe550e ? how it can changed to keep bike from over heating, or if it can.

not really comfortable with back lights and stuff like that so i was wodering how folk best do their ignition timing? i prefer a strobe but at what revs do you check when you don't have a revcounter? which position for the high/low switch? i have re-marked the crank 7 degrees in...

This is basically a timing question, apologies if it has been answered elsewhere. Can any body tell me the angular displacement of the Woodruff keys on the drive side and magneto side of the 650 Husaberg crank? In case that’s not very clear what I want to know is how many degrees rotation...

My 98 husaberg fe501e feels about as fast as my 91 Husqvarna WMX125. I have fiddled around with the carb a bit and it is much better than when I bought it. But it still feels kinda laggy. I haven't taken a compression test, but sometimes I have to stand with all my weight on the kick starter to...

I am replacing the camshaft in my 95 501FE and I need to know how to time the cam. I found a service manuel for a 99 and I have read some topics in this forum about later models. Do I use the same procedure? Find TDC using a dial indicator/long thin screw driver. With the lobes facing down...

Hi! I noticed that there´s no camchain lock on my 400 -03.How do I dismantling it? My problem is the e-start (battery is ok).I´ve talked to my dealer and he said that the extra valvelifter(centrifugalone) on the cam should lift 0,7mm.I guess mine don´t.Is it possible to weld a small...

Hi, Does anyone know why the sprocket teeth aren’t symmetrical? First I suspected it was due to wear since I needed to replace the timing chain but when I got the new sprockets they looked similar. I couldn’t see any wear at all but when I assembled the motor the valve-piston clearance...

I recently took in an orphan FE-501. The ignition was cooked, so I ordered a new SEM unit complete with flywheel. After piecing together what info is there for pre-99 stuff, all I know is the timing is to be set at 35BTC, but in typical European fashion, how to do this is not described. I...

:? what timing mark do I line the stator mark with ,the flywheel,there are two marks on the flywheel. one is longer , if facing flywheel is it right or left mark ,longer mark on left Thanks

Hi, A chain dealer in Sweden told me that Örebrokugg, http://www.orebrokugg.se/, has delivered complete timing device to Husaberg. It’s possible that they do that still.

Hi, I am no chain expert so many questions occur when I look around for information. Neither have I got any response from the companies this far. It seems that the timing chain is an ISO No 06B chain. Since my best friend is order, the fist question is if it’s possible to use another chain...

:? I have a 02 501 fe need help how long is the chain ie #of links size of chain and type . thanks

Hi, Have anyone checked the Husaberg -05 D.I.D timing chain? Has this one similar wear resistance as the old Renolds?

As i stated before I am not a mechanic but i would like to be competent enough to fix the items that seem to be require the most, stator replacement being one of them. from what i understand after the stator has been replaced the ignition has to be timed. is there only one position the...

Hey Taffy, How'd it go with the slotted cam sprocket? What kind of results did you find? Also, I searched but could not find... I remember reading, possilby before the UHE server meltdown, that one could order a chain from any old industrial supplier. I can't find the right size though...

I am trying to replace my timing chain master link the problem that I am having is the pins don't stick out far enough that I can stake them they are flush with the link and that is with the link pressed on so tight that it is in a bind I am using a motion pro chain riveter. could I have the...

Well, ive got my bike all back together, and i had it running, but it was real hard to start. I double checked the valve adjustment, it was fine. i just tried to start it and ive just got done kicking the living crap out of it, and it will try to fire a couple times but never pick up. the...

Hi All, I believe it was Taffy that stated that the older chain is better than the one currently being used, what are everyones thoughts??? Dale, etc. I need to get a new one and the steel cam gear, so this is a good time for me to upgrade. Please include a part number and/or exact...