timing

hello so im upgrading my timingchain parts because tensioner was broken. here are the questions; -03 tension arm is better than original? -05 chain tensioner is the one i need? -05 did timing chain fits? im going to order those parts, but it would be good to know that they fit and they are...

Can anyone head me in the right direction as to where to find a replacment timing chain? I had a helluva time finding the connecting rod but found one on ebay and bought it. That timing chain is the last piece of the puzzle, well then I need a top end gasket kit as well. Thank you in advance

as manmy of you know, we've had the on going saga of the rogue ignition timing since I started here. Lineaweaver warned us that the ignition could sometimes make a strobe see double etc. as the Doc says, a fresh mark needs marking on the flywheel and tipp-ex'ing. the timing mark on the...

any body no how to time 1995 fc 501? i cant figure out what stroke its on

My timing chain sounds like it has alot of slack.Is it auto or do I need to adjust.What do I need to buy to fix it.Thanks guy's

Hi All, New to Bergs, but a long time KTM owner........ I've got a brand new FE390 and have read about a lot of Berg owners fitting the Dirt Tricks timing chain tensioner to their bikes to replace the hydraulic tensioner on their bikes. Is this something that needs doing to a 2011 bike or has...

I know that is written in the DOC how to do it,but i cant understand it :oops: . For the start ,my complete clutch is taken out and so are cams and timing chain. So first put the engine on TDC ,looking at the mark on ignition timing (and checking by plug hole) Marks on gear wheels should be one...

Hi I'm restoring my 98 Fe600E, and would like to change the timing sprocket (alum.) to a steel one. And I want to have a 04+ autodecomp. Are the steel ones of the same dimension of the 98 ones ? what year ? Thanks ZAGA

I have been tinkering with the timing this afternoon. With the timing light and at idle the timing was about an 1/8 inch above the mark. I removed the flywheel and moved the stator about 1/8 and the timing light now shows it hiting the mark. The problem is that the idle is a bit erratic and the...

I'm looking for a timing chain tool for my 06 and 08 FE650

I spilt the cases on my 2001 fc550 to clean up and check out everything after a camshaft bearing let go.Fortunetly, nothing else was affected. Crank bearings and con rod feel perfect after about 150 hrs.Decided to replace balancer bearing while it's apart. My question is the manual says when...

I have a 2001 fe400 that had a camshaft bearing break and spit the balls throughout the engine. I found all of the bearings, replaced the broken bearing, broken balancer drive gear and put a new timing chain on while I had the engine apart. I lined up the dots on the new gear and placed the...

There is lots on the SEM. Can`t find how to check the Kokusans timing. Cheers spanner.

Is the 2010 tensioner any different? If yes, Will it fit on an 2009?

I have a 1997 FE 400 Elduro. Sparks just did a fine job of rewinding the stator, and I want to be sure that the timing is correct. The manual says only to release the three stator screws slightly, turn the stator to 33 degrees BTDC, and retighten the screws. Fine, but how do I know when...

Could any one tell me if you can shorten the 82 link timing chain ( part No. 200-045-03 ) by four links and make it fit the 1999 FE 501 that needs the 78 link chain ( Part No. 200-045-02). I don't know if the pitch of the chain will be the same that is my only concern. I ask this as I...

When reinstalling the timing chain can you reuse the previously pressed out link pin and press it back together or should you use a new master link?

When replacing the stupid water pump seal (again) the kickstart shaft popped out of place (again). I marked the clutch basket, crankshaft gear and top timing gear with a sharpie so I when I put it back together I could get everything aligned and timed correctly. When I pulled the clutch...

I'm going to be installing a new Timing Chain on my 02 FE501 once I get the new one from Boss. Has anyone detailed the install within this forum. Like where the sprockets need to be lined up etc.

help me out here! :oops: :oops: had a customer call last night and question my principle that the ignition timing is out and how i came to the conclusion that it was "out". essentially, having prognosed it all a few years back i have essentially left it at that ever since but it did...