engine

Hi everyone. I own a 2003 501 FE and yesterday, after 4h riding with no issues the engine died while climbing a hill. Felt a sudden loss of power like it had no gas. I had like 1/3 of the tank full, so it wasnt the problem. Then after trying kick starting and electric starting it (killing the...

I´m thinking about to buy a 2001 Husaberg FE600 Supermoto. I´m wondering about the engine. I´ve heared that 01-03 Engines are more likely to break down and a ´00 would be best (in terms of having an old engine). The engine was rebuilt recently. But what I want to know it it´s an Engine which...

I'm after a running 650 engine......any help would be great.

Help me anyone the number on Engine is not original so i dont know what Engine it is

What motor is this

Is this 650cc

What Engine is this

Hello to all!i want to ask for one problem i have recently in my engine. I have husaberg fs650e and when i start the bike i hear a weird noise in the engine,when i press the clutch the noise stops a little and when i release the clutch the engine again do the same noise.when the engine is...

I just received my engine oil ready to do its up and coming change out and realized it's 15w50 and not 10w will this be ok through out the summer months in my 03 650 ?

Hi guys! First of all i want to excuse my bad vocabulary, i dont know all the mechanical terms in english. I had this problem with my 2011 FS570 last year. The engine would stop randomly, usually when i let the throttle out and decreased speed. It sounds like when you're in a too low gear...

Hello, i am hoping someone can help. i have 08 fe450 with around 2500 miles 500 of those my miles. all of a sudden i notice a lot of smoke, after close inspection i find oil pooling up in air box, Lots of oil. HELP ME!

Hello, i am hoping someone can help. i have 08 fe450 with around 2500 miles 500 of those my miles. all of a sudden i notice a lot of smoke, after close inspection i find oil pooling up in air box, Lots of oil. HELP ME!

Hello all, Last week I found myself without any clutch. It seems that the master cylinder was leaking, so a rebuild kit solved that problem. But the problem wasn't over, so I brought the bike over to the dealership. They installed a new slave cylinder and the clutch was working correctly...

Hello all! I am starting a new project (custom build) and would need a few measurements of husaberg 600cc engine. My plan is to use old (no oil pump and no electric starter) engine, but i don't have it jet, and i have to check if it will fit. Would someone be so kind and take few measurements...

Ok, I bought this bike for quite cheap last year. It still ran, but was loud. Main bearing on flywheel side had gave up, which also made the piston eat the liner. The conrod, appears to be fine, and I feel comfortable putting it back together. My question is, the crank... I finally...

Hoping that someone one the site maybe able to assist in identifying the physical difference between the following engine parts on a 1999 FC501 Vs. a 2000 FC501. I have the opportunity to buy a 1999 FC501 engine to be used for parts in my 2000 FC501 project but I want to be sure that I can use...

For sale Husaberg Fe 400 engine In good used condition Price 650eu Only Europe https://www.dropbox.com/sh/6hqxsfb6vni1wrs/AADHq26aDpU0C7DbakwQp4ala?dl=0

I have an '09 FE450 with 305hrs, 8236kms. Bike still runs great, but I am a bit concerned about the hours. Valves have been checked and haven't moved at all. It doesn't burn oil and still starts easy and pulls hard. Oil stays clean between frequent changes. I was prepared to take the engine...

Hi! Bike: 2007 FS650-e supermotard When the season ended here in Norway:cold: I decided to open the clutch cover to check if some parts needed to be replaced, as there had been some whining-noises while riding. There had also been a high-pitched noise while accelrating fast from a complete...

hey guys i have a 1998 c400 and was wondering what years and motors are interchangable with this motor? brought bike with motor already torn down was handed a shop repair manual managed to put the bottom end back together but having trouble with the top end and still have a jar full of bolts...