engine

Hey guys, having a little trouble getting much feedback around my friend group with the 'Berg and figured I'd try the forum. Just finished putting the bike back together after I broke the first gear pin off the shift drum. I've followed the repair manual closely to repair but I am still...

There are already several threads about this, kudos to the authors! Just thought Id publish the photos from this session. To change the water seal (ie if coolant is coming out the weep hole) its a fairly small job, it can be done without removing the engine cover, just the housing needs...

Long time no Berg... See, my 650 got put up about 2 years ago due to knackered main bearings. Anyway, I picked up a new spare engine on the Bay just got it out of the box yesterday. So far it seems 100% legit. Numbers match the tag. It’s a 2008 FE550e engine. Valves were adjusted...

hi guys, i'm a new user. i'm buying my second FS650. i already have a 628cc and i'm buying a 644cc. the problem is that the ex-owner has disassembled the engine. i've never done before. but i would like to assemble the engine by my self. (i probably have all the tools) is there a...

Hi! Have swapped engine to a 550 -03 and it won't shift down sometimes. Mostly when i'm at low RPM's. It feels as when you have it in first and try to shift down. Shifting up again is no problem and I have to spam it to make a down shift. Changing the oil soon so I can have a look but...

Hi guys My engine is unrepairable and was wondered what engine other than husaberg will fit my frame husaberg fe 400cc 2001. Regards Lucas

Hi All. Hopefully this serves as my introduction as well. I have been on a 2009 450fe for 2 years now. Epic bike done some great riding in NZ. The bike is coming up on 230h and has run without fault. Had the clearence checked months ago and was perfect. I dont do hard riding since im quite...

Hi, it looks like something is wrong with my berg, it works too loud comparing to other same husaberg. Sounds come from left side. Oil bolt magnet looks covered too much also. Any suggestions what it could be?

Hi Guys, Been a long time since i have been in the Husaberg world. i originally bought an Fe 400 2002 around 8 years ago, subsequently blew that up, then replaced the engine with a rebuilt 650 from DCR. thats where the problems start... So the engine came around 6 years ago, and from the off...

I'm new to husaberg and just got myself a road registered 1997 501but looking at the engine it's got 470 stamped on it . Will the 470 top end fit the 501 bottom or will it be a 470 engine. Also will there much difference from the 501 to a 470 . Any info would be greatly appreciated thanks...baz

Hi everyone! I have an Husaberg FS 570 2011 and hope you guys can help me either calm down or find out what's wrong. I'm using the bike daily to and from work and in recent days I have noticed a strange "noise" in the engine, especially when the engine is cold and at deceleration. In my...

Hi! I was going to change the engine in my Husaberg 650 06 to an 03 engine. (do not ask why) Everything went great until I discovered that the ignition was quite different ... I have a ignition coil for both engines but can not figure out how to connect the wires to make it work. Do I need...

issue solved

Please help and point me in the right direction. My 450 sounds noisy especially on the left side of the engine. The noise sounds kinda like a bearing noise (what I can remember from two stroke bikes with bearing problems) Where do I start looking? Clutch, valves, timing chain, .... or the...

Husaberg 570 engine Newly rebuilt Was taken out as it got a rock into the bottom end and put a small crack in the sump p so we took it out and rebuilt the engine ( it had only done 10000klms before the rebuild) only rebuilt as it had to come apart because of the sump problem, when my mechanic...

Would like a complete running engine, but would be interested in just parts also. Specifically looking for cases, crank w/rod, liner & piston, timing chain & cam. Thanks in advance !---Proflow EDIT: Just in need of a 650 rod , piston & liner at this point now :)

Mine blew up. My local KTM shop said he could rebuild it but I need a new case and I'm looking at a $4500 bill. He used to work on the husaberg racing team and has a new top end laying around he said I could get a deal on so if anyone has a full engine or a bottom end that's fine with a blown...

Just doing so work on a 70° 450. Workshop manual states that the charge oil pump rotor goes in so the dowel is not visible, the opposite to the suction pump. Well unless I am being very stupid (highly likely!) mine will not go in like that and has to go in the same as the suction pump. Am...

Hey guys new here gonna be posting Here a lot my engine has ceased up I'm stripping my bike down bit by bit and any help would be very much appreciate

Im well aware they last forever sorta, but shes an ice riding girl and a lot more upper rpm riding than trail. To be safe its being rebuilt for the races this winter. Nothing found on the oil-magnet draining the oil. You got to love the 70 degree wrenchability if theres such a word, engine out...