clutch

Hi all, I am new to the forum and owning a Husaberg. I have a 2006 Husaberg fe550 that is leaking oil below the clutch cover. I was going to buy a new gasket clutch cover and install it but I cannot find where to buy one in the U.S.A. Does anyone know where I can purchase one or have any other...

I am looking for a heavy duty clutch spring for a 2011 fe 570. Who makes just a spring kit?

As the owner of a newly acquired 14 TE300 I am looking to get it set up the way I want. I have been searching for a plastic clutch case guard primarily for boot rash that is affixed with the factory mounting points. Polisport has them for the 14-16 KTM's: ...which also fits the 14-16...

Hi All Just wondering what after market levers people use? I bought a pair of scar which look nice however the brake does not fit because it is for an FE and mine is converted to Motard so different brake master cylinder and scar only make levers for dirt bikes. Regards Sent from my...

Hey guys! I ordered a new clutch cover from taffy a few days ago and was wondering what torque setting i should use to tighten the bolts with. Thanks.

Hello. Tell me please what model KTM stand the same clutch as the fe400 husaberg 1999?

Hi all, my first post on here, I've just picked up a fs570 2011. First ride out today and the clutch seems to keep losing pressure can pump it back up by cycling the lever a good few times but then it loses pressure again. Can anyone help, hoping it's a simple fix, where should I start, thanks...

Hi, I rebuild an FE400E 2002, and I have a question about the value for tightening the nut and the smaller gear. I unmounted the clutch without TQ wrench, and before read somes post of this forum. :cry: Can you give me a approximative value, I will do somes adjustement to have the...

Hi all, school me on adjusting the clutch on my new to me FS570. I recently picked it up from a trustworthy source who I believe is fairly mechanically inclined. It's been too cold to ride until recently (Canada), so I wasn't able to really test ride it when I bought it. Anyway, after riding...

Just picked up my husaberg Having a problem getting my clutch to disengage seems like the push rod is to short any ideas

Since my clutch cover needs replacing i thought of getting a rekluse clutch cover, but not the rekluse clutch which I don't like at all.... anyway it would increase my oil capacity and hence my 570 could venture further without the need of replacing oil. In theory... Anyone tried this? How much...

Hi guys, i am looking for a quick reply, cause I am stuck with no clutch and I need the bike urgently... :( On my fs 570 2011, I ended up with no pressure in the clutch lever, no leak on the MC, but he was empty..so after reading many threads here i concluded it was usual issue with the slave...

Hey guys, I've looked over similar threads in the last months; but they seem to be a little different.. i have a 2012 fe450 that (after running for a while) has a clutch issue, the clutch works perfectly when bike is cold, but when the bike has been riden for less than 30mins; it plays up...

I took my Husaberg FE450 2013 for my first ride today, first half of the day it was going awesome. Towards the end, as I put it in first gear and the clutch is still in the bike is rolling forward like the clutch isn't fully engaged. Any idea what is causing this. When i start the bike in...

Hi all, 3 rides ago my clutch faded, to fix it I laid down on the right hand side then pumped the clutch level a few times and it was good to go again. 2 rides ago I checked the fluid level and it was low so I replaced the slave cylinder seal (no evidence of a leaking from the master) and bled...

Has anybody got a husaberg 650 clutch basket 2004 for sale? Thanks Dan

Hi Looking for an auto clutch, either revloc or rekluse for a 1999 husaberg fe 400

What's up Anyone got an idea where i could get new clutch cover for my berg. Dropped my bike on the side the other day and got a crack in the clutch cover. Used cold weld on it but i don't think it will hold. Used a site Palm Springs Motorsports Online Store for my clutch discs and...

Only my second ride on the 501 yesterday, I noticed when pulling away from the lights in 1st the clutch sometimes makes a noise, is this a trait or signs of something more sinister?

I have a stripped hole for one of the m6 screws on my clutch cover. It is the one just in front of the oil sight gauge. I can tap it out 1/4 20 but I really don't know how well it will hold. The m6 helicoil uses a 6.2 mm drill bit. Has anyone repaired one of these. Also, it is the hole with...