clutch

hello, i've just picked up an 02 fe650, but the clutch doesn't seem to fully disengage? it felt like it needs bleeding as when you put it in gear its trying to pull forward with the clutch in, and you only have to let the lever out a few mil before its pulling hard, i have tried bleeding it but...

Well... It keeps going better and better... After my timing chain (see my other post), I managed to break my clutch slave while getting it out of the engine case... So I need a new clutch slave... Any options in the aftermarket ??? I called Rekluse and their adjustable clutch slave won't work...

Putting the clutch back together on my '04 FE450, and the pushrod didn't seem to want to sit flush. If i pushed it hard enough it would go in, and the master cylinder would gargle! So I removed the slave cylinder, and the piston popped out, with a small spring inserted into the back of it. I've...

Need a new clutch line for the berg part no. 81232063000. Bloody expensive US$150 or here in Australia AUS$190. Does anyone know if a ktm clutch line will fit. The part numbers or similar KTM 2011 450 part no. 54832063000 would work or any other ktm clutch line that may work on the berg...

Hey guys, Today i took out the Rekluse z-start pro out of my 2010 390, to re-install the OEM clutch. I bought the bike second hand with the Rekluse installed, so i haven't had it all apart myself before. So i managed to get it all back together without a workshop manual, started it up, no bad...

Just wondering why the Berg's run an odd number of steels and even number of fibres which leaves the steels on the outside of the pack against the alloy pressure plate & hub? I'm familiar with Jap bikes where the fibre plates are at the end of the pack against alloy. Steel against alloy does not...

Hi guys! I have a 2003 FE650, and when I start it runs fine, right untill I put it in gear, and back out into neutral( Btw Neutral is really hard to find), or if I just pull the clutch lever without changing gears. Once I do that it starts doing this really low pitched noise, but once I pull...

Hello, What is the easiest way to bleed the clutch? I was trying sort of things with no success. Probably all wrong, now my clutch line cylinder and system is full of air. Can I bleed with vacuum pump? Regards

Hi guys First post and first issue with my berg. I cannot select neutral. If I come to a stop and try and engage neutral it wont go in no matter how hard I try. However when moving forward and I dip the clutch I can select it!!! (easily) Any ideas? cheers Dave

How do I remove the piston from the clutch master cylinder? There is a piston repair kit (50302032100) I can buy but I can't figure out out to remove the old one? There is no circlip. Help?

Anyone got one? many thanks.

I managed to seize my 550, it was a total loss, so I swapped it with another 550. When I have come to fit the clutch slave cylinder, it doesn't operate the clutch. I have bled the system, but the lever is just solid, as though the actuator is pressing against something solid. I have tried...

Hi, (I was reading about some bloke who rides his Berg on the road, and who put a cush rear hub on his husaberg. Then there was a line amongst it about a damper in the clutch of recent year's Husabergs. I wonder would this make a rear cush hub a little superfluous. Does anyone know anything...

Hello Everyone, I had a pretty bad get-off in late Feb. and my bike has been sitting since then, a few of my friends have stopped by to take him for a spin, but that was about 3 months ago. So I am ready to ride this last Saturday and while going over the bike I realize that I have no clutch...

apologies mods if this should be under mechanical but figured it's more general as it's how the rekluse exp auto clutch generally affects riding on a 2012 fe570. been a few posts about it but didn't seem to be a general overview thread... there are three different models, budget restricted me...

Just realised that one tooth was missing from the big sprocket in the outer clutch hub. Now I need a new one, but the -02 bike seems to be a bit difficult. The original part number is H23014701 but its no longer available, so am I correct that the current part number is 80032000078 (OUTER CLUTCH...

Hello everyone: ). Just changed the oil 2 hours ago. OIL: Agip 5w-40 racing Lately when engine was warm and was driving...geared down and holded clutch lever down, it blocked the rear wheel, when the speed was lower, if then wanted to leave on 1st gear, it made kinda like metallic bad voice down...

Pls can anyone advise me on problems im having with my clutch, i have a 2003 501fe.. I cannot seem to get the clutch lever to work properly, there seems to be air getting into the system with the clutch working at the start of a ride and going to spongy to not working at all by the end of a...

Just install rekluse z-start pro on '05 fe 650,work nice,good idle,just a bit of drag at idle but i lowered it and it is ok,there is no slippage while acceleration BUT I HAVE NO MORE CLUTCH COMPLETLY USELESS ... ANY ADVISE i install washer on trow-out and have to install thicker steel plate to...

When the bike is cold the clutch does not disengage properly. What's the cause of this and how do you fix it? Regards Ross