clutch

Husaberg Mystery: I have a Husaberg FE 650 08 with rekluse Z Start Pro , when I bought the bike , the clutch level was hard and Not working when the engine was shut Off. I sent The bike to a Husaberg Repair shop and the mecanic "shimsed or something" so then The clutch was working normaly...

650cc, '06 Magura clutch Road chassis, clip on handlebars. Recent race meeting lost the clutch, the slave piston had twisted in the bore and the fluid lost in the engine I presume. Easy fix with new o-rings but it has shown up another problem. Because of the handlebar position the fluid...

FAO Admin: please delete

Greetings from Germany, i just finished the first production of clutch covers made of polycarbonate.. Available through: www.asbachmotors.de https://www.motoren-israel.com/Husaberg/Eigene-Produkte/Kupplungsdeckel-transparent::201961.html?MODsid=u1m6iot7r29shccr5tgb1fshr6 I have worked my way...

At launching as the clutch starting to be engaged it stics-loose-stics..The higher the rpm the worse the problem. I almost crashed a few times from zero till I recognized that the problem wasn't my clutch hand. Literally the only way to "launch" is from idle otherwise it does instant unwanted...

Hi All, Can anyone supply accurate dimensions of the clutch retaining ring, that lock in the half washers on an 03 Fe 501? While doing some clutch work we have lost the original so may make one? Any available out there hopefully in NZ would be even better (part # 23016401) Thanks

I am having a problem with the clutch on my 570 acting up when the engine gets hot. It's as if there is air in the system, the clutch lever will act like it has air in it progressively until the lever goes to the bars. Pump the lever 3 or 4 times and the clutch comes back...wait a couple of mins...

I had purchased these as backups but ended up making covers for my existing cases so no longer have use for them. The paint is worn but no deep gouges. $75 shipped for both if within the US.If you are international I would need to charge actual shipping. If my pricing is at all out of line...

Hello I`m reaasembling the engine but now I have a problem. I want to tighten the 27mm nut in the clutch hub to 120Nm. But I can't lock the gears, and the wheel is spinning. In the repair manual from 2004, it says to use clutch holder 800.29.003.000 (can't find it online) and also to...

Hi all. While in 6 gear cruising notice metallic rattle from motor. Pull clutch lever to point of clutch disengagement and noise stops......let lever out to point of engagement or further and noise returns. Notice it while cruising in 5th or 6th gear....probably because higher speed. Has...

Hello, I'm having some clutch issues and need some of your knowledge and wisdom to stop me from going insane and emptying my bank account! I've got a 2014 husaberg te300 it's always had a slight bit of clutch drag but nothing too bad. Recently though its got worse... The bike won't start or idle...

Hello Husaberg Forum The Clutch on my 07 FE450 is getting lazy.. is not fully disengaging.. so i'm going to start of by bleeding the sistem .. with mineral oil.. would you think 10W fork oil could also work?? ( its red and mineral) Thanks guys Vasco Lisbon, Portugal

Hi, When my bike gets hot usually after 40 minutes of riding or less if it's very slow hot technical stuff the clutch lever resistance begins to disappear. Eventually if feels like the hydraulic line has been cut and there is bugger all resistance at the lever so the clutch can't be...

Hello, As part of the winter refurb, I'm wondering about how to freshen up the appearance of my two side covers. The stator's not bad, but the water pump and clutch covers are peeling the paint badly. What I'd really like is some form of reinforcement - for my DRZ and 690, Thumpertalk and...

Hi folks, Read a bit in older threads, but neither wanting to necropost or clutter the other clutch basket thread, here's the issue. Like a few of yours, my bike has the starter spine/whine issue. Roughly half the times I hit the estart. I could live with it, but now that I'm elbows deep...

Righto, so finally have the bike together and running again after installing my Kibblewhite dual valve springs (Thanks for all the advice via PMs Bushy!) I thought I had this job done a couple of weeks back only to realise that the bloody kickstart mech had jammed! Sounds like this a common...

Help peeps. Can anyone tell me what type of lever replacements I need for these 2 please? Thanks <a href="http://s622.photobucket.com/user/disposablemonkey/media/Mobile%20Uploads/60325815-23BB-4BE2-9715-B8766B399FB5_zpst53et8xt.jpg.html" target="_blank"><img...

I’m in the process of ordering a custom clutch hose as I’ve gone fir a non standard clutch master cylinder. Can anyone tell me what fitting type is fitted to the actuator ? (bottom end) Sent from my iPhone using Tapatalk

Hi all In a moment of madness I decided to undo the clutch slave cylinder and set the oil/fluid free. Yeah I know, not a good plan. Anyway I've put it all back together, refilled and bled the system. The pressure is there and feels harder than it did before. However it just won't operate. If...

Hi, My recently purchased 2008 FE550 has a bit of weirdness with the transmission. I can find neutral fine with the engine off. When I start, then put in gear, no problems. But while engine running, 1) can't shift back into neutral. And 2) when running, in gear and clutch in, it...