bearing

Hi Guys Does anyone know if there's a bigend bearing available for the early type 00-03 (full circular weights) 650 crank? Has someone opened 1 up and measured it? The visible part of the pin measures 32mm. Thanks Coastie

After rebuilding my fs650 the gear from fist in second was a bit sharp/rough/jittery/clunky not extreme but just enough to anoying also the shift under light load from 5 to 6 was the same. Pulled it apart to check all was ok and was sure there was a extra washer under the spring shart with small...

Bergers, I have a quandry. I've been battling with my poor 98 for some time now. After the roller gave a while back, it's been a chain reaction. Then the tappet locknut after I adjust valves improperly, broke free and chewed the timing chain, which then snapped and link pieces gouged the...

Hey The bearing on the rocket arms has blowed on my Husaberg FE 650 2002 I have took up everything and it seems like the eninge is ok accept the bearing. Also held out the oil and looked very nice. Anybody who have experienced this before? Is it safe to just change the bearing and...

I finally started working on my 96 501 and upon inspection it seems that the timing chain wasn't the only issue with that motor. I have a 99 that I am canabalizing for the tranny but after looking at the 96 bits I want to replace the bearings as well. Do you guys have a preferred source or do...

hi all, need a new swingarm bearing kit and was wondering if these are available for an 04 fe 550, or do you have to buy genuine parts??

Does anybody know if there's a full engine bearing kit out there for a '04 FS650E? Been searching but cant find anything.

I'm cannot for the life of me adjust my clutch so that I can engage and disengage it within the throw of the lever. When I took the pressure plate off, I noticed that there was no ball between the rod and the plate. My fj1200 has it, and I'm wondering if there's supposed to be one on the berg...

Hi guys sorry for another mains question but did a search and came up with nothing. I just got some main bearings from my local bearing shop. They have given me nj206ew/c3 not the nj206ecp/c3. The bloke said the only difference is the material the cage is made from. He seemed to think these...

I was flat out in 5th gear when the bike lost power and a chimps tea party began under my arse. Limped home, dropped the oil and lots of tiny filings on the magnet, a few in the gauze filter and more in the paper filter. Off with the rocker cover and soon evident that the inlet rocker bearing...

ok,i'm on my third exhaust rocker bearing failure on my 2000 fe600e today.luckily i caught it when it happened,and shut it down.no damage to to cam this time.i have run oil recommened by dealer,and also changed oil every five hrs. with filter.never run it on side stand,normal start cold,warm up...

Hi my fe450 2004 have main bearing fail on the right size used second hand 22000 km i don't now if have repair before regards

well like the owners doc says not if but when. lost one of the cam follower bearings on my 02 fe 400. it took one of the adjusting screws with it and also made a crack in the cam cover. the adjusting screw was laying in the head, but the bearing is gone into the engine. a couple of questions...

poor ol dusty had his frag on him and i know a few more have so here is a question? has anyone ever run theirs without the inner rubber seal? and another question: did husaberg R & D phuq up by not putting a circlip on the shaft OUTSIDE the bearing and just leave a lip in the cases to...

just trying to get the SP on the faliures people have had with these in the past? i have noted a very tiny hole in the crank cheek of the '04 engines. the hole is about 0.2mm and just off the left crank journal. its aimed directly at the balancer bearings ball race. so with this in...

Help I am in need of the part number of the bearing on the counter balancer of my 1999 600fe part # 40 on the page husa number is 360 030 01 I would like to go to th bearing house and get one Let me be a little more explained the numbers etched into the bearing are the ones I am looking...

I'm not 100% sure what happened, but from one moment to the other the starter doesn't work anymore. It sounds like starter is spinning but doesn't crank the engine at all. I had a look at well known problems in the owners doc but this one seems different? Or is it a failing starter sprague...

Ball bearing Counter-balance driving shaft: 1 x 360 036-01 & 1 x SKF 61905-2RS1 (42-25-9) Ball bearing Crankshaft (standard): 2ea 360 001-01 SKF 6206/C4 Ball Bearing Camshaft: 360 000-01 SKF. 2 x 6201, 1 x 6201c3 - 2RS1 (then remove the outter seal) Ball bearing Secondary gearbox shaft...

Hi all, i´m owner of a '97 501e. Currenlty i'm rebuilding the engine. With help of this forum i got all non-oem part numbers for the bearings and the sealings...except one!!! The rollerbearing of the counterbalancer sitting in the right crankcase. I destroyed the old one so i cant read...

hi guys and gals, I know there is a thread about this but im more interested in how many people have actually had dramas concerning these bearings.Is it a major issue or been blown out of proportion? Ive recently purchased an 04 fe 550 so am wondering if it is an issue. I would prefer to here...