bearing

Between the needlre rollers in the swingarm there's supposed to be a tiny spacer. When removing the old bearings one of min disappeared. Has anyone got one to spare?

Johns thread is full of good info but i noticed the last few pages have some people wondering what to do. https://husaberg.org/t/main-bearings-failure-must-change.5986/ the ideas here are not just my opinion, there are a great many good minds who have worked out what causes the failures and...

[attachment=0:32kch7dd]1374671717148.jpg[/attachment:32kch7dd] ive got bearing pullers internal/external ive tried heat,ive even put a washer in between the bearing and casing to get a edge to hit it with a flat head screwdriver and heat just to get the pullers in but no dice anybody have any...

Hi! Im just wondering if I take the ignition cover off and grab the magnet, is there any play/movement allowed in the main bearing if I wrestle it? I mean it is verrrry little and you really need to wrestle with it to feel it. Cheers, Tom

anyone else have problems with swing arm and shock bearing kits? used all balls ones, came with wrong spacers I ended up breaking them jacking the swingarm into the chassis. (perhaps I should've stopped earlier). shock bearing seals were also ***** and fell out straight away. any recommendations?

What is considered normal play on the rocker arm bearings (axial) and axial play on the rocker arm itself when the shaft is in and installed on the head? My 570 today started to make some top end noise when idling. Heard it for the first time when I ran the motor pretty good and hot. It's like...

So I'm looking for some info forMy 2005 fs650e about the sprague gear( starter one way bearing ). I decided that since it's winter here I would takle the starting issue with my bike. For about half the summer my bike would'nt start with the e-starter button, the starter would just spin freely...

Does anybody have any tricks/ideas to getting the blind bearings out of the case halves for replacment, i have 3 different slide hammer sets but none can get behind the bearings to pull, i have 3 bearings that i cannot get to budge, i took the cases into my local bike shop who broke one of there...

Sorry for my bad english , but feel free to ask if there is something you don't understand. Bought an almost brand new 2008 Fe 650. It had 8h on It when i bought It and was in mint condition. On the last ride I started to hear a rattling and knocking noise from the clutch side of the engine. I...

My 03 FE400e started making a strange sound and losing power on my ride home. I had about 12 miles to go and it made it. I took off the valve cover an the bearing on the right end of the cam, 360 000-01, has come apart. The outer race is there, but the balls are gone. I assume they would have...

After a day out at the local mx track the other day - noticed the tell tale clunk of a dodgy bearing when I pulled the back wheel over from the top. I've only just done the wheel bearings so it's probably not them... It's not a big clunk but there nevertheless. Can't really see where the...

Hey guys, does anyone have a part number for a swingarm bearing kit for a 2010 fe390? ive searched for individual part numbers on ebay etc, all i could find was the all balls bearing kit, are they any good? seem reasonably priced. thanks.

Do I need a press to change the swing arm bearing? http://www.bikebandit.com/2010-husaberg ... #sch656444

I'm keen to get this sorted so if anyone can help it would be appreciated. I need the dimensions of the inner and outer running surfaces for the old 1990's sprague bearing? so that'll be the OD of the gear inside and the ID of the outer gear? If I can have it in mm to .01 that would be...

Hey Does anyone know if I can just replace the cam follower bearing on my 2005 fe550. I hear there is ktm part but can't find any info. Thanks

has anyone the code for the front wheel bearings on fx450 2011 . thanks

Was checking my valves yesterday and noticed that my exhaust clearances have opened up from the last time, 0.19 from 0.14. This I thought was odd but did notice that roller on the exhaust rocker arm has a small wear line on it that the intake one does not have. I looked in the service manual...

I have just purchased an 04 FE 550 with a blown crank. Can anybody point me to a new/s hand crank and piston? Rest of the motor is perfect. Is there a better fix for this model. Do not know a lot about the early bergs. Am I better off with a later engine? Whats the best way to fix this??

hi, does anyone know how i could remove the small, small bearings that sits in the engine and the clutch housing and holds the starter clutch

Hi Guys Is it better to put shielded or open bearings on the cam? I know the early girls had them open but I've heard the later years had shielded installed. What's better and why did they change? Coastie