bearing

What is better on a sunny Friday than some 70deg @150degC bbq? The bearings plopped out nice but the mains where the rollers plopped out.. So now I have to invest in a good puller. I need it anyway. Any tips?

I am trying to determine the condition of the rear hub bearings? Should the rear bushing be hard to turn? Mine are. shouldn't the bushing drop out when the wheel is removed? The bushings on my 990 fall out and roll away by themselves.

I replaced the wheel bearings in them and reused the seals as I did not buy new ones. Now when reassembling the front wheel I can see the bearing is not seated against the fork "dropouts" Is it normal to be able to see some of the black axle on the non-disc side of the front wheel?

Just had my water pump seal pop after some spirited riding on Michigan Ave in Chicago. Luckily it happened right when I pulled up to park by a retailer instead of when a young lady from Texas was standing on the island to hand me my hat after it flew off ;) Since I only had little drip of oil...

What bearing do you guys use for the balancer drive shaft? OEM is 6905 J1LLUC3 The bearing agent has informed me that this is a 'special' bearing rated for higher speed, and he cannot supply that bearing. Also, there is no 'normal' 6905 C3 sealed bearing he can supply me with. He can...

Hi all! It's been a while since I've asked a question on my 2010 FE450 but here's the story... I rode a 550 mile dual sport through SD last week and all through it I could hardly turn the bike, it wanted to go straight and gave me a very unplanted loose feel when turning. So after looking at...

H25014101 has anyone any dimensions and a lead on how to get this bearing? cheers Taffy

I changed water and oil seals with new ones but oil still coming from weep hole. Bearing has two sides so may i install it wrong side? One side of bearing has an plastic so which side i have to put oil seal? Thanks.

Does anyone know the bearing and cone numbers for the triple clamps I want to go to my local bearing store and pick some up Thanks Frank

Hi all I am in the process of replacing my front wheel bearings and seals (2013 FE350). I will also replace the external spacers as mine have been chopped out a bit. I have driven the bearings in until they contact the lip on the inside of the hub. How much of a gap (if any) should...

Hello, I just installed a bunch of new engine bearings. One of the bearings gave me some trouble. There is an ambiguous directive in the shop manual. It says to push the bearing until it is flush with the housing.... flush with the inside of the housing or outside of the housing? I...

I'm trying to work out how many of these kits I should try and put together? I'm able to source the bearings and seals in one direction and the dowels in another. so if you have one of these bikes and you'd like a linkage bearing kit would you tell me? 'normal' prices I hope/expect...

Having 170 hours on my CFB's I figured I'd better have a look at them. I'm just taking a break to share, I'll post pics later. Have got to get it back together for a dirty ride in the morning. Same part as I've done before: 59036061090 bearing complete circa $26 ea. Only had a little...

Row of powder machine is equipped with thermal power plant, the motor power of 220 kw, voltage is 6 Kv. Motor shaft extension end use 2322 e cylindrical roller bearing, the shaft extension 6322 deep groove ball bearings. In 2004, the operation of the motor shaft extension end bearing...

Hello dear I have noisy cam follower bearing on exhaust rocker arm, intake is fine. Bike is fe 501 2003. Just call dealer near me and he told be that they are not available any more. Do you know any replacement or other solution? Are rockers from 2004+ compatible ? Thans in advance

Hi Anybody got any idea of the cost of the main bearing replacement on a 2002 fs650 if done at the dealers as mine has just gone thanks

Gday all, Seems my water pump bearing and seal, is cactus, and its a 4 week wait to get one into Australia ffs, anyone know of who may have a kit here, or part numbers that are easily sourced ? This is madening.

KTM seems willing to allow axle bearings to be a premature failure point by most engineering standards. So, after replacing far too many over the years, after playing with seals and injecting grease and still not seeing adequate lifespan, I'm going to take on a project and post it. But...

hello. i was planning to get my older rim (BEHR) onto a 2001 upside down fork on my 650. As i can see the inner diameter of the bearing in the front wheel is 17mm, and the axel in the fork is 20mm. is it possible to change the bearing to a 20mm inner diameter? maybe theres a kit for...

Hi I have a 1996 Fe 400 and i cant find front or rear wheel bearings or even the sizes! If you have any ideas let me kow. Tanks Taylor