600

Can anyone give me good directions on removing the side case and replacing the clutch. Last time I took the side cover off, I didn't do it correctly and took the kick starter off and then the cover. I was told, after paying to have it put back together, that it throws off the timing of the...

Hello all, brand new here, doesn't seem to be a newbie section so here goes.. Well, I was initially looking for an XR650R for mostly road miles but with some offroad adventure thrown in. I've just been offered a 1991/92 Husaberg 600 which is in very good condition. It is set up for supermoto...

I have three husaberg bikes that I just recently purchased. 1998 fx600, a 1999 fx600, and a 1999 fc501. All three of these bike have been sitting for who knows how long. I cleaned the tanks and carbs out and changed the oil. they all fire up and run, but I think the clutch on at least one is...

Where can i find spokes ? 99 fc600? thanks!

The six speed trans is giving me problems I suspect shift forks but wanted any opinions. My bike slips into what seems like neutral , if I hold it in 1st with pressure down it will go, if I left off the gas it is in neutral again, go to second or 3rd or 4th if I don't keep pressure on the shift...

I found a like new 2000 FC600. I was wondering about the feasability of dual sporting it. Anyone care to guess about top speed of this 4 geared bike? Is it possible to change to 6 speed? Where would I look for lighting parts oem or aftermarket? Regard, -Sean

Hey All, I am so glad to find this site! I am an avid woods rider (presently on a ktm 200 2strk.)When I bought my first bike, a ktm 520, I started reading the forums and was surprised by the numbers of post describing ktm as unreliable, hard to find parts for etc. Time has shown this info...

Can get a good engine of a '02 550, but don't know if I can fit it in my '94 frame... Thanks in advance, Jerre

still having trouble w the idle.ive checked the valves there fine,cleaned the carb and all air pass.and jets.its a dellorto phm 40mm i went up a size and down a size on the pilot.it ran or idled a little better but after 15-20 seconds it would die.and thats only if the mix screw is turned in...

I have an offer of a FE600 1999 model. stands since 2 years by my dealer - probably with stator failure. the Dealer does (2 years ago) a new piston, conrod a.s.o for 1380€ and a ignition modul. After this the bikes runs about 20 min. The owner was frustrated and pluged no...

Firstly, sorry if this has been asked before.I have hus Fe600 95r ,engine is ok , but must change bearing on main gearbox shaft. I bought new bearing NJ205 ,and this is my problem because dimensions of bearing and shaft has different size.shaft has 24,09mm , new bearing has 24,93mm ...

Also what other model frames could replace a 99' FC600 frame. How about a '96 501? Can somebody post a link to a husaberg model history/model evolution page or similar? I'm trying to figure out if I can get a race bike plated by swapping the frame with a street legal one...? :oops:

Hi - I'm currently in the process of trying to get my berg back to being road-legal and one of the requirements is that it has a speedo. Bought the bike recently and it was road-registered in Japan so no prob doing this in NZ as long as it has the right bits and pieces. Been looking at...

When I bought my 600 it came with a blue larger gas tank he said it was for desert racing, anyway today I had to install a new carb to frame boot and changed the tank over to the big one. The bolt holes on the side did not line up with the frame but everything else did. Is there a bracket that...

Will a 2000 501 muffler fit a 1999 FS600E? It appears that other than the 501 mufler will fit, however it is oval shaped and not round. I was told by a dealership that it would fit. Any suggestions would be great. Thanks!

I just biught my first Berg oct. 8 2008. it is a 2000 fe600 i just got rid of my 96 cr250 wow what a differance this 600 is like a tractor. i couldnt be more happy. other than a few very minor things this bike is very clean. i like to think of my self of mechanicly inclined but most times i end...

i bought a 1997 fc 600 last year(bit of a basket case)plan being to rescue it,due to an accident since i am unable to kick it off properly,would it be poss to convert to leccy start?if so any information would be much appreciated,also does a manual exist and if so where from?apologies for my...

I've had my 2000 FC 600 engine semi torn-down for a while now. Looks like worn big-end bearings on the con-rod, plus a new camchain (and probably a few other bits 'n' bobs). I've been too busy riding the CR500 to fix the 'Berg, but now i've sold the Honda and need to fix it. What year engines...

I bought a 97 FE 600 over a month ago now and it has been nothing but trouble since 30 miles down the road from buying it. I'm no mechanic so sorry if my description is not very clear but here goes The initial problem was that it was not easy to start and would cut out randomly every half an...

1 Reliability 2 Repair and maintenance costs 3 Engine performance Who is the winner :?: