wheel

had a bike in recently no nuts on the inlet rocker pads - so they'd wound out completely! checked further in and the decomp stop had broken off. the only place this stuff can fall and be safe is behind the drive side nylon chain tube. there is a shelf there and even though one part was...

hey guys, my speedo is off (reading high), im sure its programmed for a 21"wheel (pretty sure i recall seeing 2205 for WS) anyone know off hand the measurement in mm for the 17" wheels that come on the FS650e's? thanks!

Expensive but It looks like this may be the future on dirt riding, they don´t make it for Husaberg but they say they can develop the price is expensive, If I won the lotery for shure I would get this kit "take a look at the videos is just amazing the difference" www.christini.com Hi...

When popping out the rear wheel bearings on my 97 it seemed as though the hub spacer may be slightly too long. What leads me to believe this is before I removed the bearings it felt as though they were seized. Both were very hard to turn by hand. But once removed the wheel bearings spin freely...

Sticking my SM wheels back on for an MOT on my 2002 501e (replacing bearings all round on the enduro ones and neither tyre is road legal)... Now I'm sure I /did/ have a spacer for it as there's no speedo drive .... and it's probably with the calliper bracket that I also can't find at the...

I have been asked to put together a new hub with new wheel rim. I have been told he has all the new spokes as well. Question is...where is best place to start? I have rtenewed countless spokes but never the whole lot! any tips before i end up with an eccentric hub?

For what it is worth the following is how I plan to install a 5" rear CBR 17" wheel on my 05 Fe550. Any comments / feedback welcome. My first thought is to mill the CBR hub and cush so that the "rotor to sprocket" spacing and "outer spacer to spacer" spacing is similar to my existing dirt...

Hi guys Still persevering and just got hold of a 2003 550 swingarm and 2003 650 FS shock. On the basis that a 98/99 swingarm fitted in a 2000+ frame no problem, I'm assuming that I can reverse that particular piece of reverse engineering and put the newer back end in. Q1 - should it fit...

anyone know if a dirt rear 19" wheel will fit as there does not look like there is enough room in the swingarm. I would guess that an 18" rear would fit though. edwin

once per season, with the rear tyre removed i put the rear wheel back in and check the alignment of both wheels. the advantage of removing the rear tyre is that now, both ends are roughly the same width! i get a housebrick and tie some string around it some 8" off the bottom end and then...

hello. anyone who know the diameter on the wheel bearings front and back on husaberg fs 650,2004 modell? i need the diameter because i shall maybe swap the original sm wheels against ktm cross wheels from an 02 bike so i need to now if the bearings from the berg will fit the ktm wheels kim

I noticed a little movement from side to side with my rear wheel if I grab and shake it. I was planning on checking into it but I forgot about it until the next time I rode. I did not ride long until I heard some loud thud noises. I stopped the bike and checked the rear wheel and it looks like...

Does anyone have a rear wheel lying around that they want to get rid of? not many on ebay for a berg, just missed on that went for $30. I am looking for a spare rear wheel assembly to mount a road tire on so i don't have to keep buying rear tires. I have a 99fe 400 but i don't care if its an...

hey suspension specialists out there... how can I improve front setup of my fs650? my front wheel is jumping up an down when driving from mid to high speed especially when the street is not even but "wavy"... the fork (48mm usd wp) is working at standard setup. top ends of the fork look...

I'm deciding to purchase a spoke torque wrench (Fasstco Brand) and just want some feedback from the members on what they use to keep their wheels in tip-top shape. Husaberg (FE400 2001) spoke nipples are approximately 7.0mm. The Fasstco has a 7.1mm splined head which is the closest to our...

Does anyone know were I could find cheaper (other than the OEM) replacement sensor for the odometer? This sensor mounts on the brake caliper and connects to the odometer. I just need the sensor and NOT the complete cable with connector. I would like to install one sensor per brake...

Hi there, I just installed a pair of supermoto wheels on my new '06 Fe550 and I only now realized that the odometer doesn't read accurate now with the new set of wheels (17' vs 21'). I browsed the user manual but couldn't find anything on changing the size of the wheels. So, can it be...

Would any kind member happen know offhand some bearing size information? (possibly pt. numbers, but measurement would do) I keep my bike an hour from my house, so I can't measure it at the moment, but have a bearing supplier close to home. So on to the information- I bought a set of wheels...

I can get the font wheel in the air pretty easy to get over logs and big ruts and stuff but I cant get a good wheel stand. I have tried both sitting and standing and I either shoot the wheel up so fast then drop it or I get wheel spin and it drops. my best so far would be about 30 meters but...

I got an extra front wheel form my first Berg. The problem is that it was a 2001 and my present Berg is a 2004. Is it possible to get a mod kit to fit the 01´thinner wheel axle?