water

I noticed a water leak from the weep hole, when I popped the side cover off to replace the seal and o-ring I noticed that the shaft was worn. http://www.husaberg.org/index.php?set_a ... _photo.php Is this something that warrants replacement or install new seal and leave as is? Also...

Hey all It has been too long since I too my bad water pump seal out and wanted to ask what way the new one goes back in, I have the water pump cover off, impeller out seal ready to go in and I can't remember if it goes in flat side out or in, must need some beer because this working on...

FZ RACING, install in my FE 650 an extra water bottle to increase water for radiator, they use a standard Yamaha WR450 rear water bottle and its install in the same place that Yamaha put it as standard, this is very helpful and really works. you can contact Fernando Zapater at...

Hey folks, Hitting some pretty big puddles and stream crossings today. Not quite deep enough to swamp her but she definitely breathed a bit in ( stalling, sputtering, backfiring, etc.). Any suggestions on how to make her a little more water proof?

Thought I should post this info for those who have a leaking water pump, as it seems to be a common problem. If you have oil or water leaking out the weep hole of your Berg, there is a kit available to fix the problem. Local Husaberg/KTM dealer in Orange NSW Australia John Prior, has produced a...

On my 1994 FE 501 after replacing both sets of seals and seal housing on the cam shaft and both bearings when run for 10 minutes I have water pouring out of the weep hole. Any idea of what else I can do to fix this? Please help me! Thanks

so i got 10 hours on my 03400 now. bought it last month with zero hours. is the position of that weep hole a design flaw? i got some oil leaking out now (no big deal - just a few drops) but that weep hole is pointed in a direction that is perfect for catching sand off the front tire??? Does...

I`m having a problem with water getting into rubber boot on back of the carb,not sure if it`s coming in from the air filter or not.Please help it`s driving me mad.

Hello everyone I have a 1993 Fe 350. Had a bent rocker so I purchased a used rocker cover.It had the 12mm rocker shafts instead of the 10mm mine came with stock. The casting numbers were the same and it fit. Now that I am ready to bolt on the cover I see a difference. It appears like the top...

I just recently purchased a 2002 Fx470E. The problem is as follows: There seems to be a water leak from the weep hole. Im thinking it might just need a new seal but I have read other forums about this problem and maybe should replace the bearing inside along with o-rings. Im somewhat new to...

G-day Last run out. We were riding through water and most of us temporarily cut out when charging through deep water. Does anyone know why this happens and can it be cured. My friend thinks it could be the water shorting out the spark plug cap area. I think its the carb breathers getting...

Was turned on to a new product (to me anyways) called Smart Water. Suppose to to good for keeping yourself hydrated. It contains Vapor Distilled Water and Electrolytes. And best of all (to me) it tastes like water and not some flavored drink. You can put it right in the old Camelback. I found it...

Hello all. I just got both seals that go on the camshaft from Dan at Motoxotica for my 99 FE501 but I am having trouble installing them. I noticed that the seals I pulled out had a rubber outer surround however the new ones are steel. Dan says that the ones he sent are the current...

Perhaps one of you can help me diagnose my newest problem with my 600. I was out for a short ride up the road with the beast when it backfired and lost all power. It didn't die, but I had virtually no bottom end, and no mid range. When I opened the throttle it came on in the top end and just...

http://www.lemonzoo.com/funny_videos/95 ... .html#mtop

It is certainly a design fault for this bike to get water in the carb boot each time I wash it. I want to find a way to prevent the air filter getting wet . After washing when I check the air filter I see that almost every part of it is saturated with drops ready to be sucked to the carb (...

I have been musing on the technicalities of engines with a few people recently as I often do. We were trying to figure out why trochoidal rotor or gear type oil pumps are used in modern racing engines with roller bearing big-ends/?? Bearing in mind the following: Oil pressures are...

oh dear! :oops: :oops: found some bubbles in the radiator when i started it at the weekend so i set out to re-torque the head and alas my engine is creating cappucino coffee! i have just rebuilt the engine after it's first tear-down. so to cut to the chase and i'll give you all...

I have a 2001 Husaberg FC 550. It is leaking water into the crankcase and then blowing it in the frame through the breather. I have replaced the water pump seal and the inside bearing and seal. I have also replaced the O ring on the top of the case. Any Ideas on what to do next.

The factory heat shrink tubing on my battery cables were not of the highest quality. They have all split and allowed water to get into the cable strands. I cleaned everything up and used an industrial double walled heat shrink tubing on all 6 battery cable ends. The double walled means it has a...