water

Shaft is scored and is leaking coolant. Can I replace the shaft easily ? Just the right side cover? Or do you have to split cases?

Cheap,waterproof,accurate and easy to install,hope it lasts under the Greek sun. Top Gauge Digital Motorcycle MotoBike Oil temp Gauge Meter RED LED Waterproof | eBay A local machine shop made for me a T adapter for about 20$ to connect the temp sensor on the 20mm coolant hose above the...

Last night switched from water to coolant (70/30). Ran it and no problem. Today road to wash and then downtown to work ~4 miles away. All was good. Had to shrink wrap and electrical tape the front small breather hose because pulled a "Tony too tight" which tore the hose. Happy no...

So, going in again to change the pump seal and have a question about how deep to send it into the cover. Do I need to only drive the seal until it's flush with the cover, or until it seats against the oil seal? Last time I did this, via 3 seals later, I managed to seat the seal flush with...

G'day all. Just changed out both water pump seals, oil/coolant, on my 2009 Fe390. The coolant seal was straight forward but it wasn't quite clear as to wether the oil seal could be replaced without removing the housing. It can be done. Carefully. The oil seal is backed by a bearing so there is...

need new or good water pump rotor-discontinued item mine's all chewed up from PO using too much silicone sealer in that area, thanks again guys

Hi all, Brand new to 'bergs and this forum. Got an '04 450 SE that had a broken timing chain. Got the top end all put back together. Runs great, but I can't keep water out of the oil. As soon as I fire it up, the oil in the sight glass goes cloudy/milky. I've replaced the water...

Hello husaberg forums, I accidentally dropped my water pump impeller pin into my water pump today and it fell all the way into my engine block. I tried using magnets and shaking the bike, it didnt fall out.. Any suggestions? Bike is a Husaberg FS650e from 2006.

Looking for an upgraded water pump impeller, Ballards etc to suit 650 2004 onwards

Is this aftermarket? It's fitted with a 5mm plastic spacer. Would this flow any more coolant with a standard impeller? I think Ben Ballard used to make high flow impellors for sidecar-x I'm wondering if this is one of his covers?

Hello guys. There is a seal under the bearing which number is "0625 062013". It was not seems on part diagram. So where can i buy this seal? It seems it is a special seal and i can not find it anywhere. Thanks.

Hello, Does the water pump, pump coolant into the motor or out of the motor? Thanks

My 2004 fe 450 runs great until any little bit of water hits the engine and it shuts down. The only way I can get it going again is to let it sit and idle with the hot start on for about 5 minutes

Gday all, Seems my water pump bearing and seal, is cactus, and its a 4 week wait to get one into Australia ffs, anyone know of who may have a kit here, or part numbers that are easily sourced ? This is madening.

Kawasaki Part#92049-0104 This seal, being used by some as a replacement of the OEM, is double-lipped and 5mm deep vs 4mm of the stock. Does anyone know if the extra depth of the seal will block off the weep hole inlet? Thanks. Steve

Hey guys, well I'm kinda new to bikes after wrenching on cars for years; and, just completed the Orangeberg fix, only to find water getting into the crankcase. The fix seemed without incident - new seal and bearing went in easily enough, replaced the water pump O ring, used the shrink tube...

Hi, Yes i've read the seemingly endless threads on this weep hole issue but i'm still not quite sure what needs replacing? I replaced the water seal but then i boiled the bike in some really tight single track and it boiled and flooded out of the weephole. I've checked it again and it seems...

Hi, I have a 2008 Husaberg 650 fe and I had a little leaking problem (oil) out of the little hole near the water pump. I open the water pump and replaced the seal, but everything together but know its leaking water (antifreeze) out of the hole. Any idea what could be the problem?

Hello everyone: My bike is 2011 Husaberg 570 FS.I found this hole cooling water outflow of. Please let me know how to repair Thank you

Can anyone tell me roughly what water volume a 650 radiator holds? I'm building supermono and will probably have to source or have built a rad to suit, I may try a pair of KTM LC4 rads? Any ideas