switch

Hi: I just bought a map switch for my new berg FE450 ´09. How do I install it since it instructions the map came with are no perfectly clear. How do I recognize the cable I have to plug it into?? I tried to fit on the one I though (and it fitted) buy I am not sure if this one is the correct...

According to a recent test of the '10 FE 390 in Trail Rider magazine the bike has a switch that kills the engine when the bike tips over. Apparently a fuel injected bike could run for a long time tipped over and engine damage could result. Not that I'm smarter than the Husaberg engineers but...

An electrician I'm not. I have just installed lights on my '09 FE450. For the rear I plugged in the three pole molex plug under the battery box to the rear light and I used the two pole molex with a jumper from the white (power) wire to the green and yellow wire that my schematic indicates is...

was looking at the 3 button trip switch for the new bike. HOW MUCH!! 8O forget that. anyway i have the 3 button trip switch that used to fit the 03-05 bikes. the connectors are different so wont fit the new bike but has anyone swapped the connectors and got it to fit? will it work...

Gday, I ride at a medium pace and Im thinking of getting the Mapswitch. Can I get some feedback on the FE450 performance with the Mapswitch set on soft, for technical tracks and hill climbs, as Ive only ever ridden this bike with the power set on full from factory. Thanks in advance for any...

After spending hours searching for the right components, risking few hundreds of $ for stocking them, and then having the headache of selling them (running to FedEx every couple of days) I decided to give up. It just too much work for too small profit. Therefore, I'm rolling the ball to...

Well I finally got my supermoto home after many travels and storage...what a blast! Like my enduro except hyped up on redbull and maybe crack. The lights are going off on me. Low beam hardly works and high beam turns off when I hit some bumps on the road. I am 99% sure the problem is in the...

Hi can anyone give me information on map settings on a 2010 390 my owners manual hasnt got a thing about it.Dont even have a clue where it is located

Hi, The wiring into the map switch connector has broken on me due to not enough slack. The bike is still running ( 09 fe570) and it seems to be in performance mode where i had it set, unless it reconfigures on start up. It seems to be a sealed connector, is there any way of rewiring into the...

Hey all, Could some one snap me a picture of the 09' map switch plug, either on the bike or on the switch? It would be great if you could give me a size reference or the distance between the pins as well. Thanks.

So i wanted a bit more power out of the fe450 09 and was thinking of changing the exhaust. i tried the mapping switch to the 2nd position on aggressive. oh boy. whole new bike. the way the bike rides is unreal.feels really light now. the power is just awesome. more ummmppph throughout the whole...

whato troops! i want to operate a fan on a sidecar directly from the battery and so i need a simple on/off switch BUT BUT i also need an inline fuse so does anyone make a neat switch with the fuse kinda built in/beside it. i think it's daft having a fuse flopping about.... regards Taffy

has anyone fitted the map switch to there berg, and if so how well does it work, say in really slippy situations, only i'm thinking of buying 1

Hi to everyone! First i would like to announce that i am now proud owner of 2007 550FE. It is my first Husaberg and first 4-stroke so its scary peace of machinery (in lovable and exciting way)! Anyway i cant locate front brake switch. Brake light goes on only when pressing back brake pedal...

Can anyone give me the specific location of the 2 pin front brake light switch connector? been digging around in the spagetti and havent been able to locate it yet.

Hi folks, I recently bought a replacement Brembo brake light switch (little micro-switch that fits under the master cylinder body on the handle bar to activate tail light). However, after fitting it I've noticed that the rear light is on permanently. I unbolted the switch from the handle bar...

The original map switch has rubber cover for protection from water and mud. The problem is that it is very hard to remove the cover. With one hand I held the connector for support and with the other I was peeling off the rubber cover. Obviously this was not the correct way, as my Map Switch is...

So, it seems if all I want is to be able to select the agressive map, I should be able to make a 2 position switch, 1 position open circuit for the standard, and 1 position with 6800 ohms? Correct? Anyone done this? Does it work on the fly?

I currently have no kill switch on the bike ive recently bought. Ive spoken to a few people with bike and theyve told me that the best way to stop it is to stall it?! Some one also suggested stopping it with the decompression lever on the clutch?! As in not over clued up i dont know whether...

The map switch for the new berg isnt exactly a quick change sort of switch. Is there differant swich's out there or is the map switch we have now it. It takes way too long to chage maps, the Sherco 510's switch is quick no cover to take off and replace. ?????????????????????