question

Hey there, I have a 96 Husaberg fX501 that I purchased last summer for barely anything (600 bucks) and am now making a few repairs (clutch cable, Brake lever, replace kill switch tune up, etc.) and already I must say for 600 bucks it was a steal. it runs amazing and has tons of power. It was...

I went riding yesterday and my front wheel did not seem to get a good bite like usual. I had swapped over my KTM wheels that had new tires, but a one tooth larger rear sprocket. By moving my axle forward to adjust for the sprocket, did I screw up my settings so bad that I no longer have traction...

Will a 2004 650 inner clutch hub fit in a 2001 550? regards

After my recent disaster with my 2008 650 and the lack of funds to repair it at the moment, I'm going to put my 2002 650 engine in the 2008 frame. Can I just hook up the stator to the 2008 voltage regulator, or do I also need to swap the one from the 2002 bike? The CDI I will offcourse swap...

Hey The other day I noticed I couldn't start up the bike while in 1st gear and the clutch been held. it looks like the bike wants to go forward (i.e the clutch is not working properly). I checked the fluid level and it is pretty low so I was hoping that is the reason, since I only have 13 hours...

While adding a coolant overflow kit by Motion Pro I thought I'd clean up the long snake of a breather hose that comes off the front breather hole. This bike was formerly a GNCC bike and the back breather hole is plugged and the front has a yucky hose that runs along the radiator and down below...

Hi Guys, I'm going to set the valves on my new-to-me 2008 FE 450. I've done BMW adjustor type valves but never a dirt bike with a decompression lever. Do I disconnect the spring or lever prior to checking and adjusting exhaust valves? Then when valves set ok reconnect and adjust cable free...

I came off an '07 KTM 400xcw and now have the well reviewed 390. It was a demo, so all the breaking in was done 300 miles ago. My first impression was that the bike seems hyperactive in the steering. I don't know if it's a matter of getting use to it or that I need stiffer springs but I am...

Hi, Would anyone be able to give me an idea of what fuel range to expect from one of these bikes?

hi guys does anyone know if i could fit a 2002 fairing set to a 95 model?

Guys, Sorry to be a pain and ask what may have been answered...I'm setting up to run the Delo 400 in the 550 after running 3 rides (60-80K's each) with double ester 300V and dropping the oil after each ride in order to flush out the motor....this seems to have worked well as the oil...

got a 501 with a full 450 akro (insert in) currently running a 41mm but want to go down to a 39. tried reading all the threads but theres too main. whats the best, ride up to 300 metres above sea level. any help would be great

After reading the Doc "Carburation" need some help on words PJ PAJ PS what are this? thnx.

Right, got an SPES exhaust on my 600 (Cheers Mr Clarke!) Question is, it has no packing in the end can. It does however, sound awesome. Will it hurt my bike if i just leave it with no packing in? I think i heard someone else doing it. Thanks now! Pete

Probably been asked before, but I'm new to the Forum, new to Husabergs, and new to Off-road bikes. Just scored a FE450 (2004) and hoping to do some Enduro events in the near future. The present gearing is 14 front 48 rear. Is this normal or do I need to change it (needing new sprockets and...

Will 02 plastic fit my 08.

I have a 09 FE 570 USA version and had the headlight and tail light accessory kits provided. After installing both the headlight and taillight they will not come on when bike is started. My question is... is there a jumper or fuse that must be installed? There were no installation instructions...

When changing the oil on my FC501. Should I take the screw out on the left side on the engine and fill until it starts to leak out that small hole? I'm using Motorex Cross Power 4T 10w/50 oil. Thank you, Daniel

Hey guys I have the Akrapovic exhaust - it sounds pretty loud - Do I need to modify it to be able to pass inspection in texas? if so - what should I do? Thanks Mati

Anybody have trouble with the bottom radiator/ guard mounting bolts that are supplied with the kit? The supplied bolts are about 30mm thread length. The original Husaberg bolts are only about 10mm thread length, and the thread enagages about 5mm into a blind hole, before they touch the...