question

Hi guys sorry for another mains question but did a search and came up with nothing. I just got some main bearings from my local bearing shop. They have given me nj206ew/c3 not the nj206ecp/c3. The bloke said the only difference is the material the cage is made from. He seemed to think these...

Taffy, This one is for you. We discussed the machining down of a 38mm valve to a usable valve for the inlet valve. Could you explain which valve you would use and give the dimensions and angles? Which KTM valve would you use? I have a friend that is a machinist and could help. It sure beats...

I'm trying to install a clutch from a 2002 model on my 2002 model. It is a Revloc, but that is beside the point. The problem is, that the outer basket won't fit over the needle bearings that are on my clutch shaft. Everything else looks fine. The hole in the basket on my bike is 29mm, and...

I have taken the manual decompressor off as I've never used it. My question is what do you do with the spring on the cylinder head? Do you leave it under the bolt head or do you unclip it and let the arm dangle free?

When would 2010's normally be available ? Thnx

Hi all I looked around and in my downloads and did not see a replacement part # for the fuel lines.Mine have worn a hole in the side of the U shaped line that feeds into the carb from the tee.From contact on a small hex bolt on the side of the carb.Is this part available? or do you doctor...

Hey guys I've been looking around for a skid plate. Could only find 2 options - the OEM one ($200) and the P3 skid http://www.pirieperfprod.com/p3skidplates.html which goes for $165 but looks less protective then the OEM. All the other skids I found were for older models and a lot...

hey guys ive recently become a husaberg owner, a FE650 and im loving it even though it had some problems starting for a while but a quick oil/spark/air fliter/battery change has hopefully seen the end of that problem. my problem now is that i cant figure out what year model i have as i think...

Wille - write your question here.

Ive read that some guys found the 550 turns easier than the 650, anyone know why? the 06 550 engine I have apart here has about 250gm heaver crank/rod and 30 gm heavier piston/pin than my 628 engine. the counterbalancers are the same the 628 has a longer cam chain and stroke and the...

hi all, where the clutch rod hits on both ends, one at the hyd. cylinder and the other in the clutch assembly, are there ballbearings or something like that? what i am asking is does the rod hit directly on both ends? i thought there was a little puck on the clutch assembly side but the parts...

Hi All, Hey I just noticed that my 09 570 does not have an intake trumpet like the one that is shown in the manual in the air box. Can anyone comment on this? Thanks, Dale

Hi all, I have dismounted my motor and have taken the head, and most of the clutch side components off for inspection. I do not know how many hours the bike has on it, but the crank has no play in it. Should I go ahead and split the case? I imagine that I should go ahead and perform the...

Hi All, I picked up the bike yesterday and it needs a new battery. I looked at the bike quickly and did not see an easy way to get the battery out. Is the best way to remove the rear shock and remove from the rear? Yes, I am a total newb with these bikes. I am hoping to sell my Honda...

:D Was cleaning up & ran across something that should not have been an issue to figure out. There were two different bags & had different #'s but looked the same. Here is the question ? Does the # 800-30-040-000 show up in any books you have? I have this issue sorted out, but just want...

Anybody know when the oil-pump started being used? I've just bought a 97 FE600E (pickup tomorrow) and just trying to find out as much info as I can on this model before I pick it up. The only thing I have been able to ascertain is that 96-97 was a transition year. Anyone able to shed some...

Ok so as it appears my 09 is now only a matter of a few weeks away, my thoughts of have now turned to setting it up. I put a scotts steering damper, a bash plate, alloy radiator guards and a Rekluse clutch on my 05. I guess the alloy aftermarket parts will take some time, and not really sure...

Hi there. I have a 2009 fe 450 on order. I have some fastway footpegs for a 2008 KTM I was planning on putting on it. Does anyone know if these will fit or if the husa has different geometry than the late model KTMs/last year husabergs. Thanks, Danny

Hey I will stay in Melbourne from 29th of november for 2 weeks time. The first week is for business, the second for maybe some mx or enduro riding. Does somebody know a place to rent bikes? regards DS

I've a Husaberg 450 FE 2004 and am at work ordering a new tyre. A: Does it have a 18" or 19" rear tyre? B: What size do they generally have? It has the standard excel rims. Thanks, Pete.