pump

need new or good water pump rotor-discontinued item mine's all chewed up from PO using too much silicone sealer in that area, thanks again guys

I am a new owner of 2011 fe570s,purchased 2 months ago with 40hrs on clock.Went to ride last week and while letting it warm up she began to lose idle and shut down. So I checked for spark and theres plenty with new plug.IT will start and run lean for a few second when I spray starter fluid in...

Guys, please help me out here :) I changed fuel pump this summer, however I can not make the hose stay on the pump flange for any length of time :/ I used a submersible normal type of hose that I know is submersible along with a standard hose clamp, hose is definately submersible as I use the...

I removed the carb to fix a leaking float needle valve and noticed the rod for the accelerator pump was missing. I bought the bike used and this is the first time to have the carb open. The bike runs great (as far as I was concerned :( ) so I never suspected a problem. It doesn't seem to...

I know it has been covered here a million times over BUT I have a new fuel pump for my 2010 FX 450 and want to swap it out sometime soon. Is there a complete list of things i need to get to go along with the new fuel pump, Clamps tubing etc etc? I know there is a different barbed or nonbarbed...

Hello husaberg forums, I accidentally dropped my water pump impeller pin into my water pump today and it fell all the way into my engine block. I tried using magnets and shaking the bike, it didnt fall out.. Any suggestions? Bike is a Husaberg FS650e from 2006.

Just a whoe for ebay UK and buying fuel pump. The pump itself works just fine but comes in a kit with a hose. The hose is not submersible! I got stranded in the woods and had to do the walk of shame. I gave the seller a fair chance to explain but it was all judder. Me: "Just want to let you...

Looking for an upgraded water pump impeller, Ballards etc to suit 650 2004 onwards

Hope somebody can help. I had to solder the 4 red and white wires in the wiring harness under the fuel tank . All went well pump primed everything good ,started up no problem . I thought i would make sure it was a good soldering connection and soldered the wires well.In doing this i did not...

Is this aftermarket? It's fitted with a 5mm plastic spacer. Would this flow any more coolant with a standard impeller? I think Ben Ballard used to make high flow impellors for sidecar-x I'm wondering if this is one of his covers?

Hello, I want to ask if I could change the pump connector Husaberg FX 450 2011 Magura with pump KTM SX 250f 2010 Brembo? Will it work? I am not happy Magura changed entirely in upper pump handle checked whether the lower pump misses everything was fine and still drive like a time waste heat...

Can anyone confirm whether this is simple it not? For a Berg/KTM 2013 450. Is it a case of drain oil and replace? Do I need to lie bike on side? Or is it harder and require more parts to be removed? Anything I need to be careful about?

Hi all was reading that my engine does not have a proper oil pump can any one explain how it works as it sounds like bad thing lol don't quote me but I think I read some were it has a Reid oil system :)

Hello, Does the water pump, pump coolant into the motor or out of the motor? Thanks

I'm looking for a 70 deg Billet Fuel Pump Holder/Adapter. Anyone out there know where I can buy one? Thanks, Ron

I have three assemblies that came with the bike I purchased. I will verify that they are good if anyone is interested. Make me a descent offer plus shipping. Tom:eek: I am in New Jersey USA

I am looking for the black plastic housing that holds the fuel pump at the bottom of the tank. Part underneath tank with 4 self tappers that fastens into the plastic tank. Mine was modified by the first owner, pump is now held in with zip ties. I want to replace back to standard. Should be...

So as to not be different than everyone else, the fuel pump went on my 2010 FE390. As per the recommendations on this forum I have ordered a CA Cycleworks replacement. Before I start taking it apart this weekend I have a few questions: 1. Are there any other parts I should replace when I...

Gday all, Seems my water pump bearing and seal, is cactus, and its a 4 week wait to get one into Australia ffs, anyone know of who may have a kit here, or part numbers that are easily sourced ? This is madening.

First Generation Mikuni Fuel Pump. Part number: 18-4686 Rebuild Kit: 18-5027 K&L Supply 1040 Richard Ave. Santa Clara, CA 95050 Tel: 408-727-6767 Fax: 408-727-4842 Motorcyle Lifts, Performance & Wheel Equipment, & Hand Tools