ignition

anybody know where to buy a coil in the US for a 2001 fe650e?

Hi, As the title says, what's everyone been using to protect there Clutch and Ignition covers? I've started to develop some boot rub and would like to know what everyone else has been using to prevent this? I can't seem to find anything on ebay specifically made for the Husabergs, has anyone...

Can I use the ignition of a fe 550 to built in in a FC450 who I want to use ont the road en therEfore need lights. And can I drive with 4 gears eysely on the road ! Thanks Rob

I'm checking the valves on my 2005 FE550 and am taking off the ignition side cover to turn the rotor to TDC. How much oil will there be in this side cover? On other makes of bikes I've had there has only been minimal oil on this side with it coming through a weep hole, so you didn't need to...

Hi all, Today I arrived in sunny Wales with my Husaberg (and a car load of tools and spares), in preparation for 3 days exploring the local lanes. All was good until I went to start it, only to find the key wasn't in the ignition! Having looked at the wiring diagram of the ignition switch, I...

I'm curious about the ignition map switch that Trail Tech sells. http://www.trailtech.net/040-HMS-A5C.html Does anyone have experience with this part on a Husaberg?

I just got a sicassracing keyed ignition switch for my 09 fe570. its this one http://sicassracing.com/store/index.php ... cts_id=313 anyway- i cant find anywhere on the harness when a 4 pin plug with go in- something may be hiding , any ideas?

Hi, I have some problems with setting the right ignition timing on my old (should be 1998) Husaberg FC501. Can't find any info in manuals and it's not clear how to find the mark on engine block for this type of ignition? Also, any advices how to set the right timing for engine with electric...

Hello people, I've posted somewhere else in the electrical section on my continuing woes with the inadequate e-start performance of my 2002 FE400e... in short, it didn't e-start hot or cold despite all the suggested starter upgrades and perfect mechanical condition. Many modifications later I...

Would be great if someone would make a billet ignition cover for the late husaberg engine The stock one leaks a little, at the top They are thin and could be damaged in a rocky section tip over Just a though for the after market guys

as manmy of you know, we've had the on going saga of the rogue ignition timing since I started here. Lineaweaver warned us that the ignition could sometimes make a strobe see double etc. as the Doc says, a fresh mark needs marking on the flywheel and tipp-ex'ing. the timing mark on the...

Good day all - I have the hi-lo switch on throttle side of handle bar . Is there a good aftermarket upgrade for this system ? G. S.

Are there any step by step instructions on fitting a kokusan ignition on an 02 fx470? I understand there are some pics on the gallery, but I can not find them? Thanks for the guidence :?: Also, I am in need of the wireing...

but trying to reinstall it on my bike, I cant get it to spark more than once in a session. I have the stator plugged in to the cdi, the cdi grounded to the case, and am holding the spark plug threads against the head. No regular sparking. Any ideas?

Noticed that Hyde Racing does plastic Clutch and Ignition Covers. Does anyone have these - any comments on them - should I bother at all? Thanx in advance. Fizz

I have the following problem with the ignition of my bike: Engine cold: runs normally, but I hear a few times the loss of ignition, only one spark each time. When I start to drive with a warm engine the problems seem pop up more frequently. After 10 minutes the problem is so worse that the...

Has anyone seen a built in keyed ignition system on the instrument panel on the new 2010 FE models? I swear I saw a photo of key slot built into the instrument panel but I believe it was on a non-US model. I have 2010 FE390 and have gotten it plated. I was planning on doing short rides to...

will it fit the new fs570, i was told it raisers the rpm by 1000,does antone know if it will plug straight on.

2001 FE501E OK, I replaced my stator and still no luck :twisted: .........so, I start poking around and the black and red wire has completely corroded the post off the back of the ignition switch. After looking around nobody has the correct switch in stock. So I bought a couple of other...

Hi Guys, A mate's 02 FE 400 seem to have fallen victim to a dead SEM ignition, I know we can get this sorted but wondered if it can be up graded to the later style units for more reliability long term...or is this not done / possible Cheers Pilot