head

So a bit of back story before I get into it I was having major problems with the bike fouling plugs within minutes, so I decide I'd take the plunge and change to the FCR ditching the problematic dellorto, had troubles with the switch but finally had it running and running well with the FCR...

After seeing the significant effort of combining a '96 Husaberg crankshaft with a KTM RFS 525 rod and piston (see my thread on Husaberg/KTM hybrid engine here: http://husaberg.org/mechanical/16703-husaberg-ktm-hybrid-engine.html), I'm now thinking about what to do with the other '96 FC600...

Head Gasket blown on 2006 FE550 yesterday. Rode home fine, no water in oil just spitting out of the front of gasket by the head pipe. I am going to replace this next week, should I be replacing anything else while I am in there. I have 140 hours and 3000 miles on bike. Thanks

Can anyone give me value for bottom screw? Top one is 10nm? Are there any difference beetween them - in part catalogue they have got same size but one is marked "SL" and they have got different part numbers.

Hi all Just bought a 2012 TE 300, (my first Husaberg!) the headlight is damaged, ie the glass is broke the reflector is broke as is the mask has bits broken off the back. I would like to replace it all with original parts if possible but can't find any. any one know where i can get the...

Does anyone know the head torque for a 2010 FE 390 and will the head come off in the chassis ? or do i have to remove it Thanks in Advance Stan

Good people I need guidance. The rockers on my 2002 470 are worn and for a long time would not do a feeler gauge set. The hand turn has worked fine. I think I have serious valve set recession as the valves are very tight after a old slow guy's 35-40 mile off road ride. I am due a full head...

hello ! :) i am about to send my frame to powdercoating so the bike are in pices. but i get the steering head of the bike? do the front shocks need to come of ? am i dooing it allt wrong ? :oops: first time :mrgreen: regards daniel

does anyone know why this 02 valve cover and head have a relief and some extra metal ? if you drilled through at the angle in the valve cover it would come out in a spot where an EFI injector or a NOS nozzle could work. as far as I can tell the older bikes don't have it nor do the newer...

I keep blowing head gaskets on my 2005 FE650. Does anyone know of a copper or other high quality head gasket that is available in the USA? If not, I will order from JBS.

I just replaced my head gasket and timing chain on my 2005 FE650. After adjusting the valves, I left the inspection covers off while I cranked it to make sure enough oil is getting to the head. I did not see much oil. On a Japanese bike, oil would be spraying out. I think this bike is oiled...

So about a month ago I went for a ride on my 06 650. I had just replaced the waterpump seal and it was holding fine. After making a quick stop a few miles out to gas up I noticed the overflow bottle had been filled about 6 oz. I thought this was a little strange to heat up that quick and...

Hi guys. Im trying to replace the head stock bearings but can't get the yolks off...what am i doing wrong? I slipped the forks out. Remove head nut and top yolk came off fine but lower 1 dosnt won't to drop out. Could it b seized up?any advise?

hi iv just got what i belive to be a 1999 501 as a non runner for a project and when i started to strip it down i noticed some markings on the head here is a couple of pics any info on what the mean would be aprrieated thanks in advance john

Recently I ordered the SX high compression head for my new 2012 Husaberg TE250 after being somewhat disappointed with the lack of power and torque, at least at my altitude. I’m accustomed to riding a Gasgas 300 that has head and carb mods to improve performance. I measured the compression at 145...

Hi ! I found that when I make my carb. Is my head ported or is it normal ? thks

Just reassembled my engine. It runs fine now, but the valve rockers don't seem to be getting as much oil as they used to. I didn't check the head gasket when I put the head back on. Is it possible to get it on backwards without knowing? From the outside, the gasket appears to follow the head's...

My head gasket is leaking at the low left corner (when I'm sitting on the bike). Nothing really dramatic for now, but winter's coming and I'll have plenty of time to fix this problem. I've been reading a lot and I can't make up my mind: do I get the stock Husaberg MLS gasket (Part number...

Hey guys, I need to replace the steering head bearings on my 99 501. I was wondering if anyone had a bearing number i could bring to the local bearing supply shop.

What would happen if I put a ruined head gasket in. A guy in Arizona is making copper gaskets at .042 1.01mm The bike is 2000 Fe501. stock gasket is .056 or 1.4mm What are the pros.and cons