end

Not sure what is going on but I was told yesterday that you can't get rocker shafts for the >2004s. I'm checking to see if that is for good but that of course affects every Husey going back to 1988 if that is true. However it is worth pointing out that IF I recall rightly the manufacturers...

I have had 09 berg 570 for 11 months, looking for info on the positives and negatives of removing the screw in end cap will I have to adjust FI Mapping to suit? Thanks

hello i have a 07 550 love it heaps . i have been away working for a year . back home now .but got this ticking noise in top end cant rember if it was there b 4 . had the valves done the tick is still there the power is great .runs so good . it done about 5000 km is it how it sounds or dose she...

Brought my FS650 back home from the few miles down the road where i had stored it for the last few weeks, just overtaking a car when it locked up, fortunately only a mile from home but still a long push, and then it started raining to add insult to injury. Only had a quick look at it, oil seems...

***UPDATED*** see new post below Two huge thumbs down for International Motorsports in Vancouver B.C. Canada area! :cuss: I saw an ad they ran in a local paper listing 2009 FE 570 factory demo's (including the tag line "We ship everywhere"). I enquired with my address and phone #, we traded...

I just pulled down the motor after finding a part of a seal spring on my drain plug and black matter turns out to be the seal on the mains on the cam chain side seal is gone no damage apart from mess anyone got a idea why this might have happend? the bike run fine but was feeling a bit lazy low...

how come this husky 577 i'm working on gets away with a 30mm big end? the crank is a solid piece of kit with huge main bearings. surely if what we know about the husabergs are true - the 30mm big end should be way too small? i saw it written once that it was critical that the pin was as...

Just a heads up the 35mm big end cage is silver plated. moreys heavy duty oil stabiliser isn't supposed to be used with silver plain bearings as I understand it due to (in) compatibility of the corrosion inhibitors with silver. the silver coating on the cage is very thin and designed...

My 09 570 is awesome everywhere except on hard-pack corners. It seems as though it could wash out at any stage. I have played with settings and fork height in the clamps without success. Now that I have seen that the 2010's have a 22mm offset I am thinking that this might be the way to go...

Can you see the slits I put in there ? I think it works. I am going to clean up the slits and open them up just a little bit more. I also repacked my clutch with a little bit of dog hair, that seems to be working too.

just about to try and convert a 82mm stroke crank to 35mm big end pin. i would love to have had the most hollowed out pin ya can get. anyone anyone they can trust to guide me with info on that? regards Taffy

I just blew up my husaberg fc550. The bike is only ridden as a supermoto, I want some more power, any suggestions while i have the cases split? I would love to upgrade my internals across the board, but i can't seem to find any info on options? PLEASE HELP BERG FAMILY! Also can you swap...

I have a 2002 husaberg FS550, full supermoto swap and single purpose as a Supermoto. I just lost all compression while riding friday and am figuring I'm in need of a top end. What are my options? I would like to have more power, maybe a quicker rev? Do I rebuild as a 550, can I go bigger without...

I'm cannot for the life of me adjust my clutch so that I can engage and disengage it within the throw of the lever. When I took the pressure plate off, I noticed that there was no ball between the rod and the plate. My fj1200 has it, and I'm wondering if there's supposed to be one on the berg...

I am inthe proces now of geting a set of FP race headers pipes for the Bergadapted to take my Ti Akra end can. The idea came about cos of the lack of any other headerpipes around. Any one run this sytem, or have any thoughts on what impact it may have through the rev range and on the HP? One...

Dismantled my 2005 550 recently. 129hrs After thrashing it all year, I was suprised to find little wear Ring gap was within normal limit ( But replace anyway ) Timing chain stretched like an old rubber band Piston and sleeve normal no major scratches Clutch friction plates 2 distorted (...

Hi all, i was thinking of some preventative work on the Berg this winter, mines an 08 Fe550 with 80hrs on it. does any one have any sensible pointers as to what to look for or what should be realistically replaced engine wise? i've already replaced the inlet valves and upgraded the valve...

are these available for bergs up to 2008, i've seen them on 09 model bikes (bmw450) and reckon they look heaps better than plain alloy

My 2002 FX470e is leaking a little oil out the top end. With the bike running a little bit of oil is bubleing/seeping out. My question is, do you think I should just re-torque the bolts on top or replace the head gasket???? or can I just leave it be? Any thoughts would be greatly appreciated...

hi their just a quick question if big end bearing has play or is on its way out is it possible for the flywheel to rub againts stator and cause stator casing to break off were the stator bolts to it ? iv had to cases do it to me just by kicking bike up and letting it tick over {ITS A 05 450 FE}...