end

Here we go on a top end refresh. Got timing chain,valve seals, double springs, cam follower bearings. Have everything apart and am thinking about starter problems. Will spin but disengage. Works, but since I have everything off now what is problem? Sprague?torque limiter? Thanks for advice.

Hey guys! I wanted to get your thoughts on how many hours you run your 2 strokes before you rebuild the top end? Please post your hours.

Hi Iv just put a new set of Gold speed street sport ultra tyres on my 650 supermoto Berg.Now the front end weaves at about 60 mph and above iv tried different tyre pressures but it doesn't help. Don`t think Iv done anything wrong when putting the wheel back in.Any help would be much...

Hi Iv just put a new set of Gold speed street sport ultra tyres on my 650 supermoto Berg.Now the front end weaves at about 60 mph and above iv tried different tyre pressures but it doesn't help. Don`t think Iv done anything wrong when putting the wheel back in.Any help would be much...

Hi All The berg has been grounded for months now, ive been so busy lately and it kills me to see it the way it is. Lucky for it though, very soon Ive got some time to put into it to (hopefully!) get it looking and running like new. Three months ago one of the exhaust conical springs broke...

Good evening, I just recently bought a 2010 FE570, I absolutely love it!!! That being said, I have been doing a little research online and have found that there is getting to be fewer and fewer parts available for the 70 degree Husabergs. It seems crazy to me that a bike model that was...

Can someone tell me if I can get the head and barrel off the 70 degree engine while it is in the frame. I have had to pull most of the bike apart to get the mid pipe out, ( to repair a crack around the mounting bracket and it is worn pretty bad where it slips in the silencer ) so at 166hrs I...

I need to change all the bottom end bairings on my fe400 big end, little end and main crank bairings, is it possible to do this myself? I have access to a press, but not much more bike related equipment. Is balancing essential? I'm doing the bearings then selling it, I've had enough of it now...

Hi all, I've got 3100kms on my 390 at 110 hours. She is running well but after spending 3 days punishing her in 60 metre high sand dunes, pinned in 4th and 5th gear for hours on end, I'm seriously considering a top end rebuild. I try to do my servicing myself, in the past I have replaced all...

Hi all, I stripped down cylinder head, inlet valves are completely destroyed, and also one valve seat from inlets. Since OEM 37mm inlet valves cost fortune, 100E each, I was thinking to go on Husaberg 04/KTM 35mm, did someone try this modification? What could be drop in power? Do you know...

why did Berg stop making the 570 engine in 2011? a friend of my said that it was waaay to exspensive for husaberg to make

From the all knowing Berg-meisters......... 2008 FE550 How many hours do you all recommend before I worry about piston etc (short of a leak down/compression test)?? I dont race it, I run her, good fuel, change oil RELIGIOUSLY, etc etc, normal anal retentive preventive maintenance...

I'm looking for a top end (jug, head and all) for a 2010 fx450. I am located in the States and do have a paypal account. Please send me what you have and prices or a site to find the parts needed. Thanks!

Hi, New to this forum here. just picked up an 08 550 with the 4 gallon clark tank(black tank is ugly), will be looking for a stock one soon. Even with big tank, love the bike. Way easier and nicer to ride and race then a 94 CR 500.lol Just dont like the cam chain side breather throwing...

Hey all, Getting ready to put my project all back together soon, and I've got a brand new crank to throw in my cases, just wondering about the left hand side/primary drive side shim between the balancer and main bearing inner race. I know how to shim the right hand side to allow the right...

I own (for my sins) an 02 fs650e ... after sending it away to dave clarke racing for a refresh and couple of other bits like the fork seals and stuff the bike run ok for a couple of rides then dropped the teeth on the starter motor gears, dave replaced those only for it to happen again, the bike...

Rumour on http://www.e-dirt.co.za/forum/ After a discussion with a factory insider, I learned that Husaberg production will not start again, as has already been done with the Husaberg Power parts - apparel etc. So no new 2014 Husabergs. Stefan Pierer's plan is to continue KTM and Husqvarna...

Has anyone had to do any work to the cylinder on their 450? I think my bike needs a top end and im concerned cylinder work will be needed. Anybody have any experience or a preference on where to get parts from?

Just re measured end float on the fs650 04 its been running at .5mm since last pull down still the same now leave it or make it larger???

Do the 70 degree motors make a lot of top end noise? Mine seems to have quite the valve train tic to it.