change

Hi! I have changed the kick axle and I am now not sure how to engage the clutch in order to get the exact cam position vs piston position. Se picture. The obvious answer is to place the dot on cam gear in between two dots on main gear. The kick axle retaining the arm engaging kick gear is...

I did the first oil change on my 02 fe501 today. I used the Rotella T synthetic 5w40 in a gallon jug. I filled the bike with oil till it reached about the middle of the sight glass and then started it and let it run for about 30 seconds. I let the bike sit for a few minutes and then checked...

The original bearings that are fitted to your to the range of Husaberg motorcycles are failing regularly the NJ206 bearing inner race will shed metal and put it through your engine and ruin the chrome bore and piston, KTM has the same problem on their EXC 450 -525 and use the same bearing...

I am contemplating a change in machinery, again. I purchased the WEC 496 last summer and love it. I do believe that it is the best all around enduro bike made, but catering to faster terrain. Problem is that most of my local riding areas with faster trails have been closed to public access...

Hi blokes. I've seen a 2000 FE600E which looks interesting but I'm wondering if anyone thinks the swap from my '98 FE600E would be worth it or even if it would be a good step? The bike would spend most of its time in motard trim, but would get dirty occasionally. I like my current pre-2001...

I have recently purchased a FE650S - 03 which has motard wheels, 4-piston calippers etc. Very nice bike... ... but my issue is that it feels a little too soft. Im not an experienced rider on asphalt though I have been racing motocross before. Are there any good fixes to this problem ? It...

Hallo there fellow riders! One of my front forks are leaking, what´s your opinion... should I change both anyway? When I took the fork apart I found out that both the supportrings weren´t very straight anymore.... I know that they should be flat, and now needs replacing, but why do...

Has anyone come up with an ingenious design that will help direct oil out of the drain hole, and into a receptacle? My landlord's girlfriend is into some sect of storebought environmentalism, and gets a little huffy when she sees an oil spot on the dirt driveway. I have been working with the...

Hello everyone I have a 1993 Fe 350. Had a bent rocker so I purchased a used rocker cover.It had the 12mm rocker shafts instead of the 10mm mine came with stock. The casting numbers were the same and it fit. Now that I am ready to bolt on the cover I see a difference. It appears like the top...

yes, how do you do it? do you really need to loosen the rear shock to remove the battery? /boheme

pardon me I didn't receive my owners manual and I have not downloaded anything, but the husaberg check list that came with the bike says do not change the running in oil installed at the factory till 500-600 miles. What is up with that? That is the opposite of Husqvarna, that first oil...

HELLO ! i wonder if i can replace the starter on my 02 650fe to a 2004 starter, i heard i go with a higher rpm and start better..

Hallo! I need to change my swingarmbearings. My questions are, do you have any tips to give me before I start? In other words are there any things in particular I need to be aware of? And, do you always use bearings from Husaberg or do any of you just buy bearings from a "bearingsshop"...

How many hours can i run the engine before I have to change the piston? the bike is a 96 FC 501 I drive mostly in the forest, and i dont have much rpm on the engine at all! maybe 3000-4000rpm ? the throttle is maybe 1/7 of full throttle or something like that..

02 470 the throttle pull is too hard. what gives here...my 96 was much better. also i think if the slide had rollers the return spring could be lighter and it would be easier to control (modulate) small throttle openings. so the question is what to use and where to get it (pre...

I installed a couple of the ultra thick tubes and new tires before yesterdays race. My question is.."How should a change my suspension to accommodate the extra weight.?" I felt like I was getting pounded. I was running about 18LB of air F/R. Granted I could have run less air. But since it was 80...

Hi, When changing the oil for the first time... What is the best way to clean the oil filter? Or is it recommended to replace the oil filter with a new one every time? Thanks

Hi guys this is to do with oil. I just did my first oil and Filter change on my own. Drained oil out as per Husaberg video. I did notice tiny metal flakes not many a few really fine ones mainly on the plastic and metal mesh filter (Berg is FE400 2002 with under 1500km on it). All other oil...

I got a FC 550/4 02, and think it is time to replace the fork oil. Do i need to remowe the fork from the bike, or is it possible to drain the oil and refill it when the fork still is on the bike. Needs som advises. Lucky!

Hi folks, Still enjoying my new 470 very much! I do have another question though. Today I changed the oil of my bike, but left the filter in this time. The last time I changed the oil I pored precisely 1 liter in. Today when I drew the old oil out only 0,85 liter came out. What could...