valve

Hello Husaberg community! My name is Tristan and I am from Washington State, USA. I have a 2003 FE501 that I bought a little over a year ago with ~50 hours on the clock. I put about 10 hours on the bike and it ran decently, but while jetting/tuning the carb I was doing repeated WOT runs and she...

Any of you had any luck replacing valve seals without pulling the head to compress the spring? Needing to do them on both our bikes. Mine (the wife) 09 Fe450, & his 16 Fe501s (husky). Basically looking to see if anyone has had success with the "on bike" spring compressors. If so, which 1's.

I have a 08 550fe that I just did a full rebuild on (well full breakdown and only replaced piston and cam chain because everything else seemed to be in good shape). After reassembling and getting the bike running it was very hard to try and kick after about 2 15 minute riding sessions. To my...

Hey all. Just doing my valves on the FE570. I took the cam out but the rockers wouldn’t fall back far enough to access the shims. The manual says “raise the rockers” and I remember distinctly the last time I adjusted valves I could roll them back all the way. I think. This time the intake rocker...

I have serviced my berg several times and a while decided to shoot a vid of the whole process. This video is for the 2009 on FE 390, 450, 570 and the FX series bikes. Hope this helps newbies looking to try this for themselves. Cheers.

I am trying to understand how this valve works on the FCR MX 41 of my husaberg 650. I have noticed that a spring presses the pin diaphragm which in turn opens a bypass which adds air into the pilot circuit, making it lean. A duct carries the vacuum signal on the diaphragm which overcomes the...

hi guys, i have an 08 fe450e. I've a broken intake valve spring, later on in the week ill be pulling the head to inspect the guide and seat and make sure the piston hasnt kissed the valve too hard if at all. I have some compression but not much, and the bike doesnt run. i am upgrading to a dvsk...

Cheers guys! I have been getting requests on CNC machined valve covers for the Husaberg models 2001-2008. Now I have designed covers with an o-ring seal, which will eliminate the need of a gasket. These billet covers are also tougher and will not bend as the OEM´s do. A set will cost 75€. If...

Hello! Husaberg FE450 2005 seems to have a problem. Engine ran perfectly but pushed oil trough the breather hose from valve cover. I got sure i got right amount of oil so it wasnt about that. Then i did the engine repair (piston, crankshaft, crankbearings and seals and new waterpump)...

I am checking the valve clearance on my husaberg 650 07. I have doubts to remove: 1) Can I adjust the intake valves as soon as the exhaust valves open? 2) Can I adjust the exhaust valves when the intake valves are full opened ? 3) when I screw the valve adjustment screw to move to...

Does anyone sell or know from where to buy valve cover for Husaberg 600cc

Edit: Got my answer from Taffmeister re: the cam wear. But I'll leave all this up just in case. He stated it's fine to use. After some disassembling I discovered I had a broken intake valve (right if sitting on bike) and a beat up shim laying in the head. But no other damage so far including...

A few days ago after about a 45 minutes trail ride I noticed my left leg was getting VERY hot. Made it to the parking lot and didn't really notice anything wrong but when I went to start it again I got nothing but spinning and puffing sounds from the airbox if I tried with the throttle open...

Hi, I have a FE 400 on a 04 plate, 03 model with E Start, I have read up on the 1/6 turn valve adjustment, so I thought I'd have a go, I got tdc, I believe, I undid the nut and screwed the adjuster all the way in which was a couple of complete turns, which seems to much unless I have something...

Hi All Looking for opinions on why this happend Got me a 2010 FE450 a few weeks ago Good shape , starts and works great, fast as hell Had a bit of valve noise so decided to check them , this is what i see the valve retainer is cracked and the rocker has some serious damage to it the...

Hey Guys, I got this 06 FE650 in the garage right now, one of the intake valve spring broke. I'm replacing them with Dual Springs and of course, we have the choice between Taffy and KibbleWhite. I can't wait 2 weeks for the Taffy ones to come from the UK so I'd like to go with the KB...

Hi folks, I've bought a 2002 470,fitted with a 2004 501 engine, the camchain had snapped due to a nut falling down the camchain tunnel.. I bought the bike like this, so I've rebuilt it, but im not too sure about the valve timing, can anyone help? Cheers, shug. I managed to find a 2005 manual...

Installed new oem 37mm intake valves and kibblewhite black diamond exhaust valves with kibblewhite 96-96000 dual valve spring kit, seated pressure set to 72lbs with 42crmo4+qt spring base "cups"

Hey just wondering if anyone could give me some info on getting the motor to top dead Center to adjust the valves. This is my first time checking valves so any info would be greatly appreciated. I got rad and valve covers off now just need to figure out how to properly get TDC?? My bike is a...

Looking for seals for 1996 Hsaberg FE501 Where might these be found?