size

Well after a couple of parts sagas, and waiting for spring to arrive, I am almost ready for the inaugural putt-putt on my first berg. Have been assembling tools required for servicing and I recall someone here recommending a beam style torque wrench for doing the valves but I can't recall if...

Just picked up my new valve guides, tried to get the valve in , but it doesn't fit? Could it be that the valve guides need to be pressed in the head first and then honed to the right size or did I just get the wrong guides? Part numbers match with the husa parts list. Anyone happen to know...

Hi there, I just installed a pair of supermoto wheels on my new '06 Fe550 and I only now realized that the odometer doesn't read accurate now with the new set of wheels (17' vs 21'). I browsed the user manual but couldn't find anything on changing the size of the wheels. So, can it be...

Does anyone have an approximate idea of the following adjustments for a 2002 550FC dellorto carb in the state of colorado? Which is at an altitude of approx. 6,000 Feet and going as high as say 10,000 ft. Main Jet Size? Needle Setting? Atomiser Size? I am running a 175 main Jet and it...

I was lucky enough to have a stator screw back out and break off. Another backed out some, and the third held on. Needless to say, I need to get some more screws, among other things. Anyone know offhand the screw length? (98 fee501) I see in the parts manual 5x30, I'm assuming this is the...

whats standard sprocket size on fc 470 02.??? i am running a 42 on the rear with supermoto wheels and its got to much top speed and no acceleration, only wheelies of throttle in first. what do you guys suggest??

hi all anyone know the diameter and thread pitch of the oil plug on a 2004 berg? i want to install a fumoto vavle thanx cheeseberger

Hi Can anyone give me the correct size for the H/D cam chain for a 02 650 to save me pulling the top off before I get the chain. Cheers Paul

Hello everyone I have a 1993 Fe 350. Had a bent rocker so I purchased a used rocker cover.It had the 12mm rocker shafts instead of the 10mm mine came with stock. The casting numbers were the same and it fit. Now that I am ready to bolt on the cover I see a difference. It appears like the top...

Does anyone know how to change the Wheel Size on the 04 Stock Berg computer? (I'm getting ready to add some Tard wheels, and I'd like to show the correct speed) Thanks.

I'm surprized about my sprocket sizes. Up to the impression on the power of the bike I was expecting a bigger rear sprocket and a smaller front.. before ordering the new ones I counted the teeth number on them and rear is 40teeth / front 15 teeth.. I'll order 48 rear and 14 front / I'll...

Last night I tried adjusting the tension of the chain. What happened was that the fooking bolt sheared. It's the one on the back of the swinging arm. It's approx 10mm or 3/8" but I'm not sure. Does anyone know which diameter it is?? Or which treads are on it? I'm thinking of welding a nut...

can any of you fine chaps tell me the I/D of your 650 downpipes please? they're marked as a different part number to the 501/550 pipes. also the 650 may have a different sized inlet rubber stup. what is the height as it fixes onto the head? regards Taffy

Anybody know the size (diameter and thread pitch) of the locking bolt described as #3 on page 24 of the '04 Repair Manual? It has a part number of 580.30.080.000; but instead of buying one, I wanted to make my own.

I've been searching the available posts on jetting for the Keihins. I have found that you folks out there are using all sorts of main jets with different needles. Such as: OCFMR OCEMS OCFMP OBDTM EKQ (?) What is the code for the needles? According to the '04 tech specs, my FE550 is...

I need to replace the 2 needle rollers in behind the clutch basket, but the parts manual describes them as "bushes"? Does anyone possibly know the size of them so I can get them after market? Also can the the water pump seal be purchased a/market? Thanks,

hey guys i have a 99 fe 600 currently running a 42 on the rear and i dont know whats on the front but any way i was thinking of putting maybe a 48 or even 50 on there i dont get out of 2nd when im going hard in the trails any one have some exsperiance with this...? cheers doug