shaft

Good evening to all their friends. I would like your help. Does anyone know if fe 450 2004 has trouble balancer shaft and often wants Bedlinnen; I think the manual says in 90 hours to check out. Every thought is accepted. Generally would like to know if you've heard various problems have rather...

What is considered normal play on the rocker arm bearings (axial) and axial play on the rocker arm itself when the shaft is in and installed on the head? My 570 today started to make some top end noise when idling. Heard it for the first time when I ran the motor pretty good and hot. It's like...

Hi. I have 2003 year Husaberg 650. But engine with 1-phase generator and has not "Cylinder head bleed screw". I think that engine is 2002 or older. And now I have problem with kickstarter. It slips always and engagement key kickstart don't engage. Is kickstarter shaft from 04 and newest Husaberg...

I'm assuming i need a new drive shaft seal on my FE450 ?

I've replaced the rings on my 2004 FE450, and after starting, the bike seems to be vibrating and feeling more lumpy than before. I split the engine from the right hand side, and didn't touch the left (clutch side) at all, leaving the covers in place. I found I could lift the crank slightly...

Hello folks. Former KTM owner, now FE450 2008 owner :oops: I loved the spanner time on the KTM but the berg is slowly destroying my love of bikes. Please someone help before I set light to it :evil: As usual the issue started with water pump seal leaking oil, I got it done easy all back...

Hi all. Please give me an answer where can I buy balancer bering? I don't want to buy all balancer with bering included in the service shop - it is to expensive

Hi All, After 3 attempts of fitting the clutch cover (after changing the water pump seal), the ruddy kick starter shaft keeps popping out, meaning that I have to remove clutch and align the whole sodding thing again. I've searched the forum for a way to stop this happening, to no avail. I'm...

Hi all. I am helping a m8 rebuild a basket case (04 650)and was looking for verification from someone in the know about timing marks for CRB gears. The DOC gives an explanation, but the mark on the balancer weight (factory dot punch) on the outside edge seems to line up...

ok i cant get a slipper clutch for an 02 so is it poss to fit a later main shaft ?? and are there any pitfulls to this ?? also are there any better gear ratio ? and will mx fly wheel and elec fit ? i need it to rev up faster ?? all for 650 sm thanks

One week before my first supermoto race in nearly 4 years and the cam shaft bearings collapse, luckly it happened at idle so I quickly switched her off. Striped the cam cover off and retrieved all the balls, took the left side cover off and removed some bits of bearing retainer. Now, I have some...

i am looking at removing the balancer shaft from crank cases from a 97 501fe is this worth doing to save a little weight and gain a little extra power or shuld i just leve it in.

Can anybody tell me where I might obtain a set for an 04 FE550?? The 2 thin ones?? Is it possible to run just a single wide bearing in their place?? Thanks

Hi all, great site here. So I just purchased this fe650 and didn't check it out very good. :( The shift shaft moves up/down, left/right about 1/16 inch. I went through all the mechanical posts back to early '05 but didn't find anything. Also, looking at the parts breakdown, there doesn't...

Hi, Am I able to change the seal ring on the secondary shaft(behind the front sprocket) from outside,I mean without splitting the case?

Hi guys just have a little problem with my 02 fe501. It seems as if the kickstart shaft is rotating and putting a fair amount of pressure on the casing causing it to bruise it up a bit. I tried rotating the kickstart on the shaft but it seems to return to the same position and cause the same...

I've seen a few topics like this before and know that when pulling the cases off you can pull the lickstart shaft by mistake etc. What I have is after putting it all back together the kickstart pushes through it's swing fine and returns to it's starting position however at the top position I...

I am trying to put my 04 Fe650 back together. I was warned about the kick starter shaft. So when I took the bike apart. I made sure that the shaft did not pull out. Or so I thought. When I put the side cover back on the shaft stays free until the very end when I torque the side cover...

Hi all, After fitting Orangebergs seal kit and a new water pump seal everything is fine, weep hole dry as a bone, well worth the money. The reason it was leaking coolant wasn't a worn seal but a groove worn in the shaft due to the seal, I have managed to refit the new seal 1.5mm further in...

My '02 FE400 needs rebuild.However,I can't managed to remove the swingarm shaft. it is badly stuck in its place.a couple of blows with a hammer dd not work. I also tried to pull it off by screwing the nut on one end and by using a suitable spacer between the frame and the nut but tightening the...