rocker

its split basically ... i read the owners manual bit but cant make sense of it !! "Splits easily, oil in carb if inverted. Fit Yam WR4 breather and feed down onto front sprocket or below... Re-route to get cleaner air to carb. Block underside of frame, a NAPA Auto Parts 5/8" (1.5cm) radiator...

Hey all! I'm kinda new to Husaberg but having some maintence on my bike now. Going to change the rocker arm bearings, but cant get the cap ends/shaft out of the cylinder head cover. So, how do I do it? Tried to search for a forum thread about it, but couldnt find anything.. :( Andreas

..hi today i started up my husaberg 400 and within 30 seconds what smelled like petrol came spewing out of a hose connected to the top of the rocker cover!!..its never done this before.i am guilty of not turning the fuel tap off when not in use but there was so much fluid poring out im not sure...

hi all i noticed a bit of excess side to side movement in the exhaust rocker when i was doing my valve adjustment i start by showing you the exhaust rocker then go on to show you the inlet movement and as you can see it is less. is this normal ??? thanks for your time dazza...

Hi, does anyone know if later model rockers will fit my old girl, ones with better follower bearings?

on my 2003 fe400 just done the tappets,on the inlet there is no endfloat on the on the rocker arm but on the ehaust there is some endfloat is this right,nothing looks worn but looking i bet you could put a shim in to stop this or should it be like that? :shock:

My 09 FE450 started clacking. It turns out that the intake rocker arm on teh left side is mushroomed. The shim is dished. I pulled it all apart everything looks fairly good. The wrist pin looks like it was heated up though. Anyone have similar problems?

Gents, I've got a 98 FE501. One of the rollers on the aft rocker let go and blasted through the top of the rocker cover. I just missed a replacement off ebay last week for 14.99!! Any chance one of you are parting out and need to let go of this part? Thanks in advance EDIT: Adding...

Hi Everyone, The saga of my FX 470 rebuild on the cheap continues. I noticed some roughness in the rocker roller bearings and upon inspection found flat spots on both of the central shafts of the bearing. No wear was detected on the needles or outer race. New bearing assys were about $70NZ...

Yesterday we were out and about on the trails. About and hour into the ride my '03 started to make a very loud noise from the top-end. The noise increased/decreased with RPM. Shut the bike off immediately so see if there was an obvious issues, (loose exhaust etc...) Nothing obvious. Did a...

This is what i got out off my 2 FC550 '02 Engines. The rocker shafts are totally different, en in 1 of the rockers there is a hole, witch the other one does not have? rockers, 1 from engine #1 (upper) and other one from engine #2 (lower) The other 2 rockers are identical :roll...

I was flat out in 5th gear when the bike lost power and a chimps tea party began under my arse. Limped home, dropped the oil and lots of tiny filings on the magnet, a few in the gauze filter and more in the paper filter. Off with the rocker cover and soon evident that the inlet rocker bearing...

Quite some time ago I put 03 rocker arms in my 2001 FXe 470. To date it has not been started as I have other bikes to ride and don't want to get it dirty. I did not drill them for oil pressure relief and really can't remember if the original ones had holes in them. Its my understanding that...

ok,i'm on my third exhaust rocker bearing failure on my 2000 fe600e today.luckily i caught it when it happened,and shut it down.no damage to to cam this time.i have run oil recommened by dealer,and also changed oil every five hrs. with filter.never run it on side stand,normal start cold,warm up...

This weekend I dismounted the cover of the cylinderhead an was astonished: The rocker arms are only lubricated by the oil of the timing chain. I now mny former 2001er modell, which has had a oil canal from in the cover up to the rockers. (remember the little o-ring seal ) When is...

So, my 05 fe550 barely gets ridden. It only has 5000 miles on it (240 or so hrs). The cam chain still has a couple clicks of adjustment left, but I figure I should replace it before long. I've adjusted the valves 6-7 times over the life of the bike, and they are always pretty close (i use the...

05 FS650E Second time now but at 400 engine hours and 10,000 miles on the clock should I complain? First time was at 176 engine hours and 4600 miles. Bike was running great but I noticed a drastic increase of little silver hairs on the magnetic drain plug. Some additional investigation...

i have cleaned up my old rocker cover for the third time with a gentle rub on the sheet of glass and i now have a high point with it sat ON the cam. fair enough! i always knew this would happen but i thought i'd ask before i try it, if anyone had tried knocking out a gasket to do the job...

who has experience installing 2003 rocker arms on 2000 year and older husaberg models?i am specifically trying to find out if 2003 rockers can be used on a year 1996 husaberg?thanx,dan

i found a follower on my bike in spec after i'd pulled the pin and looked at it for wear. but i found the tiny needle rollers inside have been thrown against the outside: the rocker arm wall and grinding in deep. they make a kind of spiral trough which gets deeper and deeper until its deep and...