question

Just got my FS shock back from servicing, and removing the spacer. It's full length now, like my FE forks. I searched and can't find an answer. I want to rotate the bottom of the shock and install it so that I can adjust the rebound easily-er...from the left side. My chain slider is...

The small threaded inserts that the 6 mill bolts holding the side plastics on seem to come out a little too easily after a lay down .I'm new to my FE 390 and am wondering if this is a way to stop the plastic from breaking or weather they've been pulled out too often.

:eek: 2004, 650 Hus Got oil leaking from weep hole, was just a few bubbles of water but now oil:( From reading earlier threads on this much discussed subject I understand that the water pump seal can be changed by just removing the pump but to repair the oil leak the clutch casing needs to be...

From the all knowing Berg-meisters......... 2008 FE550 How many hours do you all recommend before I worry about piston etc (short of a leak down/compression test)?? I dont race it, I run her, good fuel, change oil RELIGIOUSLY, etc etc, normal anal retentive preventive maintenance...

Anyone used the upgraded S2 Halogen bulbs in the stock 570 headlight holder? i was looking at using something like the 45/40w BA20d found here: 45/40w S2 Halogen KTM Upgrade Bulb [21-301] - $14.95 : sicassracing.com Will that make too much heat for the standard headlight light holder and...

Hi everyone, Looking to install a hidden kill switch on my 08 Fe450. Is there any harm in splicing a toggle switch between the oem kill switch wire and grounding it... (kind of like a redundant kill switch that would be permanently grounded until the circuit is broken manually) OR...

Hey all, just picked a 14 te 250 last Saturday. This is my first berg. My question is do the 2014's not come from the factory with the map selector switch anymore? I thought I remember reading that the 12-13's came with it? Thanks

I've tried search, but did not come with a definitive answer, so here I go. `10 FE390, around 190 hours, just acquired recently, don't know if valves were checked before, this is my first check, measured values are: (IN should be between 0.10 - 0.15mm) IN#1: between 0.13 - 0.15mm (ok) IN#2...

Howdy gents, I'm a first time purchaser of a delightful 2004 Husaberg FE450. It runs like a champ, with only 2255 miles on it, however it has been rebuilt. Unfortunately there is absolutely no info on the internet about the parts interchange between various years and models. I was hoping you...

Hi guys! A quick question...does a SEM coil from a 2002 650 fit a 98' 600? Thanks, Tom

Hi, I have a 2011 Husa FS570 The rear rim is 4.25 which calls from the factory for a tire size of 150/60/17 I found a sweet deal on a Q2 tire thats a 160/6017. I will save about $50 total after mounting if I go with the 160, over the tire I was leaning towards the Pilot Power in the...

Good afternoon all, So it turns out that my question pertains to an SEM stator in a '99 VOR 503, which I understand is very similar to, if not the same as a Husaberg unit. Anyways, the stator harness has only 3 wires coming out of it, which all go to the coil. As with other brand stators...

Is the bike still suppose to run if u fully turn in the fuel screw? It also only starts whitout choke and stalls if I pull the choke even a little, cold or warm no matter. Cheers, Tom

Just wondering if anybody has powdercoated anything in the husaberg yellow. If so what color code did you use, I'm having a hard time trying to match the paint to my plastics so it matches. I want to powdercoat my rims twotone half yellow and half blue. so any help would be appreciated

hi all,as title states ,, i have only had the bike 2mths and only got it started yesterday for the first time. What would be the best recommended oil to put in my 03 husaberg 650 ? its a tad smokey when i started it up for the first time,but to my knowledge the bike has sat for 2yrs and not been...

Hi guys! Quick question: can the bottom part of the front shock absorber be removed? Im talking about the part which holds the wheel shaft in place? Cheers, Tom

I'm looking to buy an FE, I know that much. Background: has bikes, trikes as a kid, love good stuff, am an advanced level MTBer with very good descending/technical skills. 42 and 190lbs, decent shape. I'll be dual-sporting the bike, with the intent being to get from one stretch of dirt to the...

Should i be using 10W 50 fully synthetic in my 2009 fe 550 . I have silkolene . How often should it be changed

hey, i have a set of excel pro series supermoto wheels on my yamaha, but these wheels are pretty much universal, the mounting for the brakes and sprocket is interchangeable, but they dont sell mountings for husabergs, but they do sell them for ktm, so im thinking since ktm is making the...

Hi All Will a Rekluse clutch that came off a 2013 fe350 fit the new 2014 fe250? I know it wont fit the 2013 fe250; but mybe the new 2014 fe250 with DDS clutch will?? plse help