issue

hello there, its been more than a while since i last posted here! here 's the deal, i rebuilted the whole engine few months ago due to a broken camshaft bearing. con-rod, cam shaft, all bearings (except of the gearbox ones) , camchain, piston rings, rollers, etc . all these were replaced. the...

Gurus, I have a new 2009 FS 570 here in Lima Peru. I purchased this from run out stock and it now has 45 hours and 2000km's. Last week while riding home I pulled up at a set of traffic lights and it stalled which was odd. The bike since then has developed a very erratic idle issue that isn't...

So before i just start looking for one though it would run my problem past the husageniuses.... 1st off bike ran great all last fall on the road and winter in the feilds, i noticed the last time in the feild before i took off the knobbies one quick stutter at low rpm slight acceleration and...

I'm currently riding a 2011 FE570S. Prior to this bike, I've been on a KTM 525 and a Honda XR650. In all I've run over 57,000 miles on these bikes with approximately 80% being off road miles. I've tried multiple brands of tires, but for many years now, i've been running the Kenda Trackmaster...

i am currently working on my husaberg fe 600 and it back fires and is real hard starting. i pulled the flywheel cover off and found top tdc and the flywheel marks dont seam right. I have a pdf i found off this site and it shows the flywheel in a total different location than what my bike shows...

I have a new to me 2005 FE550 with a lighting/signal kit installed. When I bought the signal lights weren't on, but the switch and wiring were present. I have been through the whole system and referred to the wiring diagram, but can't get the signals to light up at all. I've connect an ohm...

Just tried to fit new friction plates to my clutch, it was worn out but not cooked. The new parts must be too thick, or I am?! There is no play at all in the clutch at all now :? , do I just need to find new four new plates 1mm instead of 1.5mm? Or, is there a simple way to remedy this? Is the...

hi, newbi on here with a problem got FE570 & clock/dash and only works intermitten, checked all connections, when dash comes on there is r6 code. cant find anything in manual to help

I'll start. 09 FE570 100 hrs approx 2000 miles. Bike flamed out on me 1/2 dozen times in the first 30 hours. Adlusted the idle and had the ECM reflashed, no problems since. Changed the drive chain at 70 hours due to a little surface rust (no sprockets). That's it. Change the oil about every 15...

2005 FS650E 4700km's Less then 100 hours The other day I noticed the Horn doesnt work before that the Hi-Beam indicator stopped working after a trackday I believe the Vibrations killed the bulb...I dont really care so much about the horn I believe its probably a fuse (if that makes cent) But...

OK, here's the deal, I was in a desert race Saturday, had gone approximately 40 miles when I took a low speed spill going down a hill. I fell to the right. The bike was still running after I went down and then it died before I got it picked back up. After I got it picked up, I hit the button, it...

Hi All, My dealer installed EE radiator braces on my '09 FE590. While riding an event on the weekend I noticed I had a coolant leak coming from the top area of the rads. Turns out the T-shaped radiator hose that runs between the two radiators and runs through the frame is 1/4-3/8 of inch...

Lads, 2 things I'm looking at, 1. first, read on this site I'm sure about milling 30% of the brake pad away to reduce rear brake locking...I'm struggling with my 550 on semi loose / loose downhills with the rear being impossible to stop from locking up. If I was to try the...

I got my new BERG 390 and the first ride after one hour of use the bike stalls and didn't want to run.. At that time I was using a AKRA slip on and I was told that the 390 was not accepting any exhaust till I get the reflash mapping thing in the ECU, so I thought that was the problem.. After...

Hi, new to the site - Lots of info, thanks. I have an issue on my 2010 FE450. When descending down a hill, running the motor against compression, the bike begins to accelerate. This happens in any gear. It seems that the exhaust sensor is analyzing the increased heat whilst running against...

OK My 550 will start fine when its been sitting in the garage , on both E start and Kick . It also starts fine when hot . But when I take it off the ute after driving to a ride its a complete bitch to start , roll start seems to be the only thing to start her up . Any ideas ???? I m thinking...

Hey there guys, just putting together my 04 550 engine and am finding netural between 3 and 4 gear. Cant understand or find out in the workshop manual which way the shift drum should sit or which way the positioning star should sit on the shift drum...

I got my 09 berg early last year, and bought a scotts damper mount kit, and fitted it as per the instructions. Later I removed the headlight assembly and replaced with just a plain front number plate, but left the majority of the wiring that was attached to the connector bracket mounted on the...

Hi all, I purchased a 2000 FE501 about 2 months ago but I have never been able to rev it more than about 1/3 throttle or the engine dies. Person I got if off is no help. I have replaced the Stator, CDI and put anther carb on it and it is still doing it. When you rev it up, you can do it...

Hi Guys, Well as I await the last of my bits to arrive from O/S for the 550 I've undertaken assisting a mate with much needed service work on his 2002 FE 400. It's got 1900K's on it and to say it was visually in mint condition would be an understatement...but visually is...