gear

hello all, I just bought a 1997 Husaberg fe400 and its a blast to ride. the bottom end has a ton but once I get half way through the RMPs it starts to bogged down really bad.... I am new to Husaberg so I don't know much about them mechanically. my guess would be these bikes are geared low for...

Hello! Is it ok to leave the small needle bearings in engine case when i remove the starter gears? It`s my "new" -03 450 engine and i have no experience of those modern engines ;- ) Cheers Jampe

Hi all I have a very slow oil leak from my gear selector shaft, where it pops out from the left side engine case. As far as I know its a simple o-ring fix and most bergs do it to a certain degree anyway, but mine is beginning to get worse. Im going to tackle it before it completely lets go...

Hi All, Looking for Husaberg riding gear. Specifically pants and a jersey. Anyone know who might still have some in stock. Can't seem to find any anywhere. Thanks!

I just bought a 95 Husaberg fe501. The only thing that is wrong with it is the one way gear is shot. I am having a hell of a time figuring out how to remove the timing chain though. Does anyone know of any kind of video or free manual that I can get ahold of that will walk me through it step by...

Does anyone know where i can acquire a Husaberg leather jacket, and or Husaberg helmet. Best regards Estin

In need of 36 mm x 1.5 mm drive gear puller. O.E . part number much appreciated. Thank you in advance Dale www.lineaweaverracing.com [email protected] 510 223-9052

Hi The gearbox of my 02FE400 works great without any strange noises, my problem is with the 4th gear. In 4th gear and when I push it harder it will jump to 3th gear, it doesn't make any strange sounds or anything, it just comes to 3th gear. If I don't push it harder it doesn't jump. It's been...

My new 2011 fe 570 only had a 90 day factory warranty so it was necessary to perform all severe stress testing immediately while still under warranty. One of the first stress tests was a series of speed runs on interstate 279 near Pittsburgh PA. The first test runs were with the stock gearing...

Guys, Just wanted to ask if anyone has found a good after market shift lever that'll fit my 04' 550. May need to go back to the standard unit. I got one of Taffy's as a spare and when it's fitted it seems the spline is a little out of synq. The head of the lever is either somewhat to...

My FE390 of 2011 doesn't want to start in 1st gear anymore, but it always could. It also has become harder to find neutral. Blead the clutch with new fluid Magura blood. There is a lot of drag when you try to push it with the engine off in 1st and clutched and a big clack when put in first gear...

Hi guys, last few rides I have, bike sometimes go out of gear on jumps or on high speed small jumps. I doesn't happen often, one time on ride, sometimes even not. Yesterday I was in 4th gear, on jump it went to neutral and when I leave the throttle it engages again. Any suggestions what it...

Hi Guys, I am in the process of purchasing either a 2010 FX450 or a 2011 FN390. Can anybody give me the ratio breakdown on the tranny's. I just sold my 2005 KTM MXC and I wanted to compare the ratios. I am mostly interested in 1st, 2nd and 3rd gear ratio. I live in Arizona and do mostly single...

HELP!!! I took apart the clutch cover to put a new shift fork in. The kick start gear came out when I pulled the cover. I am not able to get the kick start gear to stop grinding on the case and it has no tension on the up stroke of the kick arm. I have the spring in the back side of shaft and...

Hi All, Having some sticky gear changes with my 05 fe 550. Recently (10hr) did a rebuild. Changed gearing a little since then. Impossible to get it into neutral from 1st if standing still. Is this a worn Clutch master/slave cylinder? Not enough pressure to fully release plates? or something...

Does anyone know what way the tread goes eg left or right on the gear torque wheel to pull it apart and shim it????? and the best way to hold while undoing the bolt. :cheers:

the sprague inner gear known as the freewheel gear for the 2001-2002 models has been discontinued. I sold my last one yesterday :cry: :cry: if I recall, fitting 2001/2 to 2003/8 or vice versa causes a whining noise? and I can't imagine this gear being made by anyone else for anyone else...

Hey I road my 1998 600 fes yesturday and it lock in second gear and would not come out. I got home and took the cover off and got the selector thru the gears again but dont want this to happen again when riding a long trail. Is there a part I need to replace or do I just need to do an...

Hello All, I have a brand new Husaberg TE300. 2012 model. Now have 5 hours on the new bike and love it. However.... In the first and second gear power doesn't seem to get distributed properly. It not running well. As soon as change into 3rd gear, the bike wants to take off. 3rd, 4th, 5th...

so i am needing to get my kick-start off and gear shifter to get the cover off. But i can not.i think that when the po stalled then engine and tried to restart it, something happened to the kick-start. it got all chewed up. anyone have any help for me? I dont want to break anything. here is some...