front

Apologies if this topic's been covered many times before, but can someone point me in the right direction? I intend to use my '04 501 for road use only, mainly A & B roads and am looking for a set-up that affords rapid acceleration and power, without too much emphasis on top speed... 80'ish mph...

I have just orderred a 12 tooth front sprocket for my FE390; can someone confirm that: - it is 'turn clockwise' or 'anti-clockwise' to get the original one off, and, - what torque do I tighten the new one up to in Nm; do I use loctite? (my other bike a Husky 610 sprocket is held on with only a...

Hello everyone, first post on UHE. I own an 05 Fe 501 which had a new rim and tire fitted last summer. When riding the bike on tarmac I get a bouncy undulating cyclic movement through the forks. I guess this is an issue either with the rim or tire. However I wondered if there may be other...

Hello Does anyone know if its possible to get an official Husaberg/KTM blue supermoto front mudgaurd? I know they do yellow, but I'd prefer a blue one. Anyone got a link to an online shop or a shop number? Thanks

The bike is new to me and I am trying to get equipped. Motion Pro Rider Wrench has been recommended. Which size should I get? I was told the rear is 27mm, but I don't know the front. Anyone with a quick answer? Thanks.

I got some 4.6 wt race tech springs to replace my standard springs on the 2008 berg. They are apparently the right springs for the bike. I notice that the race tech springs are 3cm longer than the standard WP springs. Has anyone else noticed this? This will clearly affect the preload.

as title, im wanting a 16.5 front wheel and a 17 rear pref 5 inch wide :)

Anyone have a good one. I saw Flatland has one but I'm thinking maybe going with a carbon fiber or plastic deal. Anyone happy with what they have?

Hey guys, My front fender rubs my frame and has some scratches on the fender and has rubbed some paint off of my frame. Is this typical? Any good fixes for it?

I just changed the oil of the fork legs, and put both of them back together. I tried compressing each leg by hand and there seems to be much more rebound damping on the left fork leg. There is exactly the same amount of oil from the same bottle in each leg. I also checked that the preload...

my 02 front brake lacks so much bite and power (and it's been getting worse) that i finally decided to do something about it. the rotor appears very smooth and polished with no grooved texture and i wonder if it's just too hard. i don't recall folks complaining of bad rotors on ktms or...

I had read on this site that the front fender on the '09's were easily broken, and I discovered this personally this last weekend. The bike fell over while parked and the front fender folded under as it hit a rock. When I picked it up, I saw a six inch crack in the fender starting at the...

My 09 570 is awesome everywhere except on hard-pack corners. It seems as though it could wash out at any stage. I have played with settings and fork height in the clamps without success. Now that I have seen that the 2010's have a 22mm offset I am thinking that this might be the way to go...

Got one of E-bay to fit my 03 650 SM but the magnet on the disc that activates the speedo dont pass near enough to the sensor to activate it. what have other people done to over come this?

Which way does the bolt turn?? It is really on there tight. Not surprising, but after turning it a bit it is still very tight. When I encounter this I always wonder whether I am loosening it or tightening it. I know that some drive nut/bolts on various mechanical machinery has left handed...

Hello Does anyone know where I can buy a front number board online in the UK for my 07 FE550E? I've found KTM ones http://shop.jimaimracing.co.uk/acatalog/Front_No._Plates.html The part number 50308007000xx comes in black which is ok. Would this fit? Is there anywhere that sells yellow...

Hey All, Will the Husky 2 stroke counter sprockets fit the 07's? Do the newer 2T Husky's work? Thanks!

Two of us with bergs have noticed we do not get all our travel in the front forks. These bikes are used for enduro and not font wheel landings. As there are two bikes we have experimented by changing to lighter springs, lowered air chamber as far as allowed, reduced dampening etc. Has...

Hi there,any tips on replacing my front sprocket oil seal ?(2003 FE400E) 100hrs,

Wondering of anyone has found replacement axles with a pull handle ? Also do the KTM parts for a similar year cross over ? Any suggestions ? The bike is an 06 FE. Thanks in advance... Darren