fork

Ok, can't figure it out. Got my 2010 FE450 which I love but tend to lay over once in a while. I've experienced what many others have in that the fork gets twisted and I have to loosen and adjust back straight. I've noticed for some time now that the spacing between the tire and fork covers is...

After doing some reading on supermoto set ups I've discovered that you need to bring the fork rake inwards towards the engine. Is this true on the 09 Fe450 enduro? Who makes an adjustable rake fork / triple clamps set up , rough cost and set up time between enduro off road and supermoto on road ?!

hello ! is about to buy a FS (2006) front fork to my 650 2002 (fe) . does it fits ? great upgrade ? regards daniel

New FE 570 and was installing a set of Seal Savers as I had great success with them on my KTM. When sliding down the plastic fork protector I noticed how the plastic fork protector and the Seal Saver were rubbing - just a matter of time before the Seal Saver wuld be shredded and interfer with...

Anyone know when you can download the official "Front fork setting list" and "Shock setting list" for 'bergs? I've managed to blag a couple of photo copies from the dealer, but they do not specifically say they are for my 2011 FE570. The ones I have are article numbers 14457K02 (fork) and...

anybody out there having datasheet for 'old' husaberg usd. front fork, i wish to know what it looks like inside. sorry for my spelling. i know it is not a good excuse but i am danish. thanks

hey, just changing the fork spring on an 09 450 and when removing the cap it left a brass threaded thing with a slot in it on top of the damping rod? upon trying to re thread it into the cap it come against the male part of the clicker and becomes a pig? any tips? and is it right that it...

Hi Everyone, Quick question, has anyone swapped a set of KTM 640 LC4 forks onto a 1997-1999 FC 501 before? How difficult or easy is the swap, any advice welcome!! :) :?

Hi, Since I bought a new 2011 FE 570, almost every time I bleed the air from the forks, a little of oil is coming out from the bleed hole. It is like 5 cc or sometimes even almost 10 cc (I guess) coming out from each fork. Is this normal? I feel a big diference on the fork after I bleed the...

Looking for a set of .42 front for springs for wp48 mm forks 2001 fe650 Pm me if you have something located in north America Thanks

Does a specific model ktm spring work in the front of the 01 48mm WP forks. I've searched here and around the web. Not finding much info. Mine has 46 springs in it which are much too stiff. Thanks

Hi Guys.. Looking around I read a few guys are impressed by the Kawasaki fork seals for their Bergs. I recently purchased a pair of Seals from some where els (Pyramid Parts). But, after the install (a serious effort alone), before a single ride. They are showing signs of leaking oil over my...

My forks have a top out spring. And when i extend (compress the top-out spring) I get a gap between the fork cap and compression spring. is that right ? Regards

I must be either f_k_ng blind or dumb, or both. i cannot find the amount of fork oil required for my 2008 550. I searched the database here and my Owner's manual and found nothing. i did, however, find info for a 09 570 and 98 501, but nothing for an 07 or 08 450, 550, or 650--which i assume...

Does anyone have the stock shim stacks for the 2011 FE450 CC forks?

What is the stock fork springs in a 2010 E450 US model? thanks HusaRod

Hi all going to update from 2010 fe570 to 2011 fe570 i have resprung for my weight will the fork springs from the 2010 go into the 2011 cc fork? Also i have had the rear shock revalved for the 2010 and was going to swap it to the 2011 is there any difference in the rear shock for this model. Thanks

So, having read all the archived posts.......... Just doing the seals on my FE501 02 - blew one big time last week on the local MX track - searches here say anything from 100mm to 150mm. Doc says 115 - 130 so guess 120 is as good a place to start as any. This is with the springs out I guess ...

Hi guys: Since I bought my 2.011 FE450 (which I love by the way), I thought of the cc suspension to be much better in responsiveness as the previous models with open cartridge. The only thing is that it felt way to soft and it bottomed a lot (in small jumps). So I ask the dealer to compressed...

I was woundering if any of you have the stock stack for the Husaberg fe450 2011 CC fork. I`m having a 2007 sxf 125 CC fork and thought that the Fe cc forks stacks from 2011 should be a good start. The fork i have had ProAction valves in them so i got the stock ones and softer mid spring so far...