fe400e

Hi New to Husabergs as I have just aquired a 1999 FE400E with a few issues, previous owner stated it need finishing off. Just replaced fork oil seals but am a little puzzled by how much oil to add, always done it on volume on previous bikes. Can anybody help please? Thanks Paul

Hi, I bought my Husaberg one month ago. I got problem because bunch from speedo is cut so I have no idea how to repair it. Can anybody help me? This is picture of cables inside of speedo http://img713.imageshack.us/img713/5366/speedox.jpg Thanks a lot Ted

Several months ago I posted about my 98 FE400e locking up with a THUNK. I haven't had the time to dive into it until this past weekend. Here's what I found: One of the intake valve adjustment bolts broke. I found the end that pushes the valve, but the bolt is just plain gone. I've pulled...

Hi guys I'm new to the world of Husabergs. I have a chance to buy a lightly used 03 400fe, really good shape, it runs and goes down the trail fine onlyon the 2nd rear tire, original owner. The power seemed very similar to my 01KTM 400RFS. I can see no issues, but I would like to hear the good...

Now that I have finally got a chance to use my bike, gotta tell you I am very impressed. It works much better on the street than I thought it would, and gets about 55 miles per gallon. Even with the cold, rainy weather we have been having here in Pa,,I am loving the commute to work! Thanks again...

Hi! So I have a FE 400 E Berg. And i think i might have the stock battery, but still the elctric start just can't start the engine. It's tee weak, and when the piston reaches the tdc the electric start just dies. Too much compression for the starter. So, what would i do to make the electric...

Hi! Last time when i was riding with my pal we exchanged the bikes for a moment (his FE 400 2000y my FE400E 2001y) I noticed that his Berg is more powerful then my it pulls like crazy from idle ,and it,s completle vicious 8O . My is smooth like sheep and gives power away more predictably...

Bike wont crank, but when it did last week it sounded as if it was running half throttle...could not get the bike to idle down. Carb is clean. Stock jetting. Cannot find any air leaks. checked fire... will jump 12mm air gap, but will only fire 2-3 revolutions and then quit for 2-3 and start...

The recent destruction of my rear hub also took out my chain guide. I can't find one for my bike at Bike Bandit or Boss Bergs (just '09 +). Where can I get a chain guide for the old girl?

As you may have seen from my last post (I was the guy whose sprocket split in half taking by hub with it) I am in the market for a new rear wheel. Which KTM wheels are compatible with my 2003 FE400E?

Hi, i have '03 FE 400 with worn out e-starter clutch, i don't have money to buy a whole new 04+ unit and I'm wondering if i can put only the sprague from 04 model in my 03 since it is the most worn out part in whole assembly. Outer gear is slightly worn out but not nearly as much as sprague...

Hello, I just picked up a 2000 fe400e. The bike does not run at the moment due to a bad stator and while I'm waiting for a new stator I thought I would take care of a couple other issues with the bike. One of the problems is with the kick starter. When you push it down, at about the half way...

I'd like to get my hands on some rad braces for my 03 FE400. I don't want full guards as I do not want to comprimise cooling (often I ride with my kids and the slow pace comprimises cooling). Does anyone know where these can be obtained? Will other braces (e.g. for KTM) fit or be made to fit?

Recently sold my 03 FE400 only to buy another. This one came fitted with a Big Gunn muffler which when repacked although a little loud wasn't to bad and has better power noticeably down low. I removed all the electric start gear as I couldn't get it right with my last one and they start so easy...

Hi I have BIG troubles with fouling sparkplugs, now in one week i have burned two DCPR7E and two DCPR8E plugs. Today i stucked in the woods, --> about 5km's of pushing the bike away. :evil: Now i'm back to garage and did some inspection.. Old SEM gives ~50volts at Red / Black wires with...

Hello to all berg riders out there! In a few days I'm about to turn 16 and after riding a 2-stroke light enduro for a year now (Yamaha DT125) I've been looking at taking a more durable and serious bike now. One reason I don't want to stick to a 125 is that in my country there really aren't...

I was reading the Doc and found the section on frame idenifying numbers. My 10th digit is a 3 then is 0000008 which to me would be a very early 03 model however compliance states 8 month of 02. I dont have the forks with spring preload adjustment caps and am also wondering if my engine has the...

Does anyone out there know if there is any alternative positioning for the starter relay.I've checked on the "Better than new" doc and can't find anything.Looks like extending the battery leads and cable tie around the frame just above the carb to me,any other ideas ?.

Anyone got the resistance values for my coil,I've got a new stator and a spark but not sure if this is breaking down under load ie won't start.....

Hi there,on the trail of the cursed bad cold start.I have stripped my carb down and all jets are standard as is the needle clip position, now looking for wear.My bike has only done 60 hours so I have checked for ovality in the main needle jet (atomizer).Not oval but after inserting the needle...