cover

WOW I got Mine in the mail today and I must say again WOW I was expecting something kinda good but this is great. With out a tape my 4 Dos XX beer calibrated eye says this thing is about 5/16 billett aluminum aniodized blue with a gasket and thumb screw...

Hi, I'm sure this is elsewhere on the site, but with my lunchbreak coming to an end, I still don't have an answer and my bike sits sadly in the garage. What size are the orings for the top oil filter cover (for lack of a better term)? The inside one was worn, and it got pinched in two last...

I have been thinking about making some air intake covers to put in place of your filter while washing your Berg. How many people from the UHE would be interested? I have not drawn them out yet or figured cost, I just want to get an idea if the market is there.

Research did not reveal any info on this item so please excuse if this has been hashed over already. Has anyone tried or had experience with the Boyesen Quick Shot Accelerator Pump cover for the FCR Keihin?Supposedly this supplies fuel to the motor in greater volume and with more velocity during...

http://www.husaberg.org/modules/Gallery/albums/LINEAWEAVER/IMAGE0007.sized.jpg http://www.husaberg.org/modules/Gallery/albums/LINEAWEAVER/IMAGE0004.sized.jpg

Hi ,any one know if I can fit a 04 ,or newer 2 piece clutch cover on my 02 501. thanks

This is the first time I am going to work in the engine and for a start I have to fix a leak coming down from the rocker cover. What's the best way to remove the cover? Do I have to remove the radiator? I hope that the issue comes from the sealant and I intend just clean up and, re-apply...

Husabergers all around! I got my -99 501 FE some month ago, and it didn't take long to get stator problems after riding in very wet conditions (bike dies when it gets warm and then starts like nothing and runs well for a while when it has cooled down). I start to understand this os quite...

I made a billet ignition cover with two 1/2-14 NPT threaded holes to do the ignition modification. I also add an O-ring to seal better and I add an extra 1/4 of an inch to make room for my fly wheel weight. I was wondering if there is an intertest for people wanting one of these covers for...

MOTOEXOTICA & G&G CYCLE BOTH CARRY THE REINFORCED SILICONE VALVE COVER GASKETS FOR 450/550/650 NO MORE LEAKS , JUST USE LOCKTITE RED ( HIGH TEMP )SNUG TIGHTEN THESE SEALS ARE SILICONE WITH A FIBERGLASS REINFORCEMENT SO THEY WONT TEAR......... 8O

Hi I have a FS650e, leaking a fair bit of oil from the front. It's coming from the cam/rocker cover gasket. Took apart and resealed using Blue Hylomar at the weekend, it was dry as a bone but I noticed this morning it's weeping again. On closer inspection the sealant it peeling off! Are there...

I have a leak coming from the bolt under the oil level window. When I removed the bolt, a bit of oil was dripping. When I torque the bolt back, without overtorquing, it seems to stop for a while, only to drip on at a smaller pace :evil: What do you suggest I do? I think it needs to be...

Okay I have looked but can't find the thread that was being discussed recently about the best sealant for the rocker cover can anyone point me there? also, does anyone know if there is a "rebuild" kit for the dellorto seals and gaskets and such.

250 204-01 Inspection plug ignition cover 99- Anyone got any of these??

If this has been mentioned before... excuse me... but A perfect cover to stick over the air filter whilst power washing her down is cheap and easily available over here in the UK from Screwfix Direct. Over shoe covers No. 29124 Will last you forever... certainly longer than your Berg ...

Hi all have just had the frustration of finding that the thread in the head for the rocker cover bolt which goes through the exhaust rocker pin is stripped. have just had new rocker bearings put in by dealer after i removed the rocker cover myself. when putting back on had difficulty as...

:( The weld repair went well, but valve cover did not remain flat enough to seal against the top of the head. Still leaks. SO, I was wondering if any of you Berg mechanics have a good used valve cover available for sale to fit a 2002 400e. ? . All I need is the cover; my rocker shafts, arms, etc...

:( I had a bolt come loose on the head cover casting and now it is cracked. Cracked good. 2002 FE400e. Question: I maybe cannot buy just a cover because of the cam bore, but can the cover be welded up and align-bored as a repair option? I haven't heard of this problem yet here at UHE, but you...

My local dealer is no longer selling 'bergs so if anyone knows of a dealer, and preferably on the west coast, who has the black piece of plastic that covers the battery please PM me their name and phone number. I don't know how I misplaced it in only a weekend but stranger things have happened...

I was poking around the KTMTalk.com pages and ran across a posting concerning broken cam cover bolts. Since the new Bergs are put together in the same plant, the bolts probably come out of the same bin during assembly... Has anyone had any problems with broken bolts?