cover

I can't get the left hand engine cover off. I've removed all the bolts The water pump cover The water pump impelllor The kick lever The kick rubber seal. The gear lever Gear lever seal It will move around the top and the back but seems stuck on the bottom front area? Any advice very much...

Guys, In trying to sort out my rocker arm/valve issue, I came across what looks like an oil leak at the top of my ignition cover, where the wires enter the housing. Here are some photos: Imgur: The most awesome images on the Internet http://i.imgur.com/RL5kINZ.jpg Should this be as...

Hi all, I am new to the forum and owning a Husaberg. I have a 2006 Husaberg fe550 that is leaking oil below the clutch cover. I was going to buy a new gasket clutch cover and install it but I cannot find where to buy one in the U.S.A. Does anyone know where I can purchase one or have any other...

As the owner of a newly acquired 14 TE300 I am looking to get it set up the way I want. I have been searching for a plastic clutch case guard primarily for boot rash that is affixed with the factory mounting points. Polisport has them for the 14-16 KTM's: ...which also fits the 14-16...

Hi, by default there is liquid silicone sealing between the cylinder head and the rockerarm cover (Engines 2000-2003). I was wondering if it makes any sense to build a "real" gasket for this part, since I'm afraid that small crumbs of silicone will clog oil channels in the engine somewhere...

Hey guys! I ordered a new clutch cover from taffy a few days ago and was wondering what torque setting i should use to tighten the bolts with. Thanks.

I have Husaberg parts for sale. All parts are new from the old factory in Laxå, Sweden. I have seat covers, complete seats, gas-tanks, plastics, breaking disks, some Electrics, (no stators or cdi) , feders, cylinders, etc. I answere easiest way throug my e-mail: [email protected] I...

So my clutch cover cracked, which is an easy fix. But I want to put a "case saver" on it so it doesn't crack again, I have looked and I can't find anything. Do you guys know where I can find something that fits or do I have to make it myself ?

Since my clutch cover needs replacing i thought of getting a rekluse clutch cover, but not the rekluse clutch which I don't like at all.... anyway it would increase my oil capacity and hence my 570 could venture further without the need of replacing oil. In theory... Anyone tried this? How much...

Looking to shine any light on this issue, any one suffered similar? I imagine the issue could either be caused by bearing failure or crank spread? What's my chances of repairs?

hello I'm looking for a husaberg 125 2012 ignition cover to buy has to be international shiping. the part number is 503.30.502.300 original or aftermarket??

Hello guys, So i have a fs650 '04 with a broken valvecover. Got 2 550 and 1 450 covers and partnumbers match. But the right side has a 4 digit number stampt on head and cover. They match as a set. But my question is are they interchangeble (do i say this right?) and why do they match in...

Look at this. This is what offroadboss had. No longer available. His picture on the left. How do you paint it like picture on the right?

What's up Anyone got an idea where i could get new clutch cover for my berg. Dropped my bike on the side the other day and got a crack in the clutch cover. Used cold weld on it but i don't think it will hold. Used a site Palm Springs Motorsports Online Store for my clutch discs and...

I have a stripped hole for one of the m6 screws on my clutch cover. It is the one just in front of the oil sight gauge. I can tap it out 1/4 20 but I really don't know how well it will hold. The m6 helicoil uses a 6.2 mm drill bit. Has anyone repaired one of these. Also, it is the hole with...

I am looking for a valve cover for my fe650 from 2005. The valve cover should be the same of the 450 and 550 models from 2005. I need the cover without the waterpump on the cover.

Hello I am looking for a Husaberg clutch cover (blue) for my 2011 Husaberg fe570s Thanks -DaBergman

Cylinder Head with valves and springs working perfectly when it was mounted. And Rocker Cover with rocker arms and bearings in good shape. Cylinder Head with valves and springs----->80 € Rocker Cover with rocker arms-------> 40 € Everything ------->100 € All of this parts are...

Has anyone bothered to redo there seats? Thinking of redoing my 650's seat and was wondering if anyone still makes covers for them. Leaning more to the idea of getting my local upholstery joint to do up a griper style seat with a random pattern. any thing to stay clear of?

Anyone ever had the clutch cover on a 501 2003 stuck on by the viewing window? Got all the bolts out and it's all loose except for round the viewing window. I'm close to getting it off with a club hammer. Tia