bearings

Trying to source a set of rear wheel bearings for my 01 fe650e. Not too much luck. Do KTM bearings of the same year work. Lots of searching and no luck. Thanks

Anyone tried ceramic wheel bearing? I am told: a. no rust b. lower drag c. resistant to heat d. last longer

Hi Everyone, just registered and need your help. Have just bought my first berg, 2007 fe450, need to change the rear wheel bearings ,wheel is off the bike no visible ciclips, internal spacer is rotating freely , how do you remove them :?: normal weather here in the uk, wet ! but need to get out...

does anyone know what rear wheel bearing are in , i mean what number is the bearings.

Im going to try and replace my mains bearings on a FS650e 2003 myself and reading the Doc it says “Also put the cases in the oven and the bearings in the freezer for a long time before doing this. This allows full expansion or contraction of items.” How long is a long time and at what temp, I...

One week before my first supermoto race in nearly 4 years and the cam shaft bearings collapse, luckly it happened at idle so I quickly switched her off. Striped the cam cover off and retrieved all the balls, took the left side cover off and removed some bits of bearing retainer. Now, I have some...

Has anyone got a good fix for the front and rear wheel bearings as far as stopping water from getting in. I have a brand new 570 and done a creek crossing. I can see where it gets in on the front between the axle clamps on the bottom of the forks and goes in along the axle shaft to the centre of...

Can anybody tell me where I might obtain a set for an 04 FE550?? The 2 thin ones?? Is it possible to run just a single wide bearing in their place?? Thanks

Hi! My first post on this forum :cheers: i am from Polland and own 2001 FE400E i need bearing numbers for my Husa from All Balls SWINGARM KIT- UPPER OR LOWER HEIM BEARING- HEADRACE BEARINGS- It s hard to be Husaberg owner here in Poland nobody knows anything about them :roll: Thanks!

is there any good ways to get the innerring from the mainbearings of the crank if I dont have the special tool? or should i spend a few hours making one like this http://www.husaberg.org/modules/gallery ... ullers.jpg

hi i was looking in the docs and found this photo of a crank bearing, its got 3 screws around it to hold it in the case is this something you guys are doing or just a trail? does it work?

Just thought I'd put some info out there that I got from the local SKF dealer here in Bundaberg, QLD. I was getting a bottom headset bearing for my 550 ($33.00AUD) & asked about where the bearings were made. He replied it doesn't matter where they're made, SKF use the same processes to make the...

I just pulled down the motor after finding a part of a seal spring on my drain plug and black matter turns out to be the seal on the mains on the cam chain side seal is gone no damage apart from mess anyone got a idea why this might have happend? the bike run fine but was feeling a bit lazy low...

hi just bought 07 fe550 has 55 hours 1977km 2 owners, had major service 400km ago, valve clearances checked all the checks everything ok. nw just wondering are the 07 valves titanium or stainless, do the have big issues with valves wearing out in seats. also on the husaberg website it says...

so I'm pretty sure my steering steam bearings are freezing up, time to replace, bike is 2 years old and never been greased except what little was done at factory. question: do I need husaberg bearings ? or would KTM have the parts too? if I do need husaberg parts, where do you suggest...

Hi all My 04 needs swing arm bearings Is this job doable with only a vise and no press any tips Thanks :D

these are the 4 bearings that hold the sprague and the starter clutch. two reside in the cases and 2 in the left cover. can anyone tell me any specs on the size of shaft that is meant to fit in them? i guess that it's 8mm but can anyone say they have seen it on paper? it's just that...

Hi Guys, just a quick question,are you able to purchase cam folower bearing kits for the 04 bergs or do you need to replace the whole rocker arm as one complete unit.I have used a bearing kit only on earlier model. See YA!

Im replacing the cam bearings 6201/c3. Now do I get rubber sealed bearings or open ones? Also I have replaced the Cam follower bearings, is one centre punch enough to hold them in or should I do both shoulders? ie each end of the pin?

Hey Guys, Haven't got as far as pulling the wheels off the bike yet but was putting togthr a list of spares as I went along and just wondered if the wheels bearings on the 04 550 was an unusual size or if they're common and can be sourced from a bearing shop.. If common...