arm

Hey can't describe it right, the swivel ends that sit on top of the valves at end of rocker arms, 2 have a fair bit of movement, a lot I think, TAFFY do you sell these as a Replacement??[attachment=0:1s9mf85v]image.jpg[/attachment:1s9mf85v]

After a day out at the local mx track the other day - noticed the tell tale clunk of a dodgy bearing when I pulled the back wheel over from the top. I've only just done the wheel bearings so it's probably not them... It's not a big clunk but there nevertheless. Can't really see where the...

Do I need a press to change the swing arm bearing? http://www.bikebandit.com/2010-husaberg ... #sch656444

Looking for a catch tank to fit behind the swing arm, I've seen one on a ktm but can't find one! Any body know where I can get one in the uk?

hi all i noticed a bit of excess side to side movement in the exhaust rocker when i was doing my valve adjustment i start by showing you the exhaust rocker then go on to show you the inlet movement and as you can see it is less. is this normal ??? thanks for your time dazza...

made to allow your calfs to rest against and reduce arm fatigue, made to screw into the rear sub mount holes. Can't wait to try them out (is not bolted up tight in these pics)

Not been riding my bike as much as I would like I've been really busy at work, but I've still been training very hard, well imagine my disbelief when out riding an extreme course I got arm pump so bad I couldn't hold on, is this normal?????

Hello all, went for a snow rode yesterday and lost my kick starter. Anyone have a kick start arm and bolt for a 2007 fe550? The starter don't like the cold and the snowmobile trails are calling me!

Hi all My 04 needs swing arm bearings Is this job doable with only a vise and no press any tips Thanks :D

I just got back from an 80 mile ride and the swing arm is getting looser every time out. The nut is tight and it looks like its only the right side. Is this going to be a pain in the *** ? Should I deal with this sooner than later ?

I have confirmed that the screws that are intended to hold the chain slider protection on the swinging are are m6 on the 08 models, however, some come with M5 screws? Does anyone know when the screws changed and whether the m6 is better than the m5 and cups that secure the protection strip?

Yesterday we were out and about on the trails. About and hour into the ride my '03 started to make a very loud noise from the top-end. The noise increased/decreased with RPM. Shut the bike off immediately so see if there was an obvious issues, (loose exhaust etc...) Nothing obvious. Did a...

has anyone used a stiffer detent spring or played around with the profiles on the shift star ? ours seem like the spring is weak (comparitavley) and since its the spring that actually shifts the gears and nor our big foots at all 8O a stronger spring seems like a good idea. then there is...

Ok Boys, Just spending Sunday morning doing some more set up work on the 550, I'm taking out the swingarm to check / grease bearings etc...I've pulled the hex head bolt out of the bottom mount of the shock \ swing arm area and there's no doubt a pin that needs to come out in...

I ride a '06 fe550 and always suffer from throttle arm pump while warming up, so bad I can hardly hold on. I'm a good rider and always lift weights to keep in shape. I've heard it all like: Avoid alcohol the night before, Drink lots of water, take aspirine.Then I wonder if my stock 14/48...

So, my 05 fe550 barely gets ridden. It only has 5000 miles on it (240 or so hrs). The cam chain still has a couple clicks of adjustment left, but I figure I should replace it before long. I've adjusted the valves 6-7 times over the life of the bike, and they are always pretty close (i use the...

05 FS650E Second time now but at 400 engine hours and 10,000 miles on the clock should I complain? First time was at 176 engine hours and 4600 miles. Bike was running great but I noticed a drastic increase of little silver hairs on the magnetic drain plug. Some additional investigation...

Did a re-grease & check on my head stem bearings a week or so ago, managed to hold the forks and pack grease into the bottom bearings and do the top bearing / whack a bit of extra grease into the head yube for good measure, so didnt actually remove the whole box and dice. once I had it back...

hi guys love my berg to bits but its looking a bit tatty now so i have new graphics and plastics! put them on the bike looks great getting the new seat cover on this week! the only thing is the swing arm looks crap, just wondering if i could fit a newer model swing arm? mines a 2000...

i found a follower on my bike in spec after i'd pulled the pin and looked at it for wear. but i found the tiny needle rollers inside have been thrown against the outside: the rocker arm wall and grinding in deep. they make a kind of spiral trough which gets deeper and deeper until its deep and...