400

Hello everyone! I ask for help in removing the camshaft to replace the seals and then adjust the intake and exhaust valves. 1.How to remove the camshaft? 2.As to configure valve, what should be the clearance in the intake valve and what in graduation! Thank you in advance for your help!

In need of an FE400 flywheel My bad one has a stamped number 101 801 05 Z and is a SEM type K

Hi all. I'm trying to reset my motorcycle. fe 400 98. now it has a carburetor dellorto phm 40 I would like to see it on my bike or not. And help with its connection where what hoses connect. In advance excuse for English I from Russia and peshu through a translator.

Does anyone know where I can find a wiring diagram for a 98 400? I tried searching the forum and found one link but it is broken and just dumps me on the Husqvarna website. I replaced the stator (Thanks Taffy), but haven't been able to get any spark.

we have ordered just 10 con rods for the 1990-1995 350 and the 1996-2000 400. they are due at the end of next month-May. we have taken two pre-orders so 8 left. when i get these in it will mean that all tthree early engines are covered again for the first time since the factory...

Hello Need some advice here So I got a 1997 FE 400 E with the stock VHSB Flatside Carb It starts OK runs Good in upper throlttle pull hard , but with small throttle opening , like just above idle it's rough , hesitades and stumbles , once past this it' rev hard and fast I've cleaned...

Hi Bergs, can anyone help me ? I am trying to find which type of bearing and gasket is used in the front wheel in my Berg FE 400 2003. Unfortunately, there are no spare parts in Czech e-shops for 2003. Also Berg representative sells parts only up to 2004. I hope that bearing and gasket is...

Hi all you freaks, few weeks ago I bought HSB FE 400 (2003). After many machines I've owned, finally, I found the right one which absolutely fits me and I want to keep FE for a long time :D. Unfortunately I am facing a serious issue with cold start (two weeks before my planned trip to...

just finished the basic first testing on my 99 fe400 drz ignition swap! starts better than new,timing advancing, great throttle response! really quite a simple swap! i'll try to post picture soon!

Hello all I just got me a 1998 FE 400 E, and runs well but needs some work Needs a batteey, front rim is cracked and some other small stuf Slight bog on small throttle openning, but will need carb cleaning first Need a side stand, mine is broken, can anyone tell me how long it should be so...

thinking of buying a 2002 husaberg 400 any one have info if this is a good year any issues ?

For sale Husaberg Fe 400 engine In good used condition Price 650eu Only Europe https://www.dropbox.com/sh/6hqxsfb6vni1wrs/AADHq26aDpU0C7DbakwQp4ala?dl=0

hello! First oil change after rebuild revealed a little grey oil. My guess It's the waterpump seal. Because it deformed a little bit while i installed it. It was a really tight fit and the metal seal was a little bent. I'm wondering if its possible to use ktm water pump seal. Dimension of my...

Further to a previous post I made the husaberg 650 I thought I purchased turned out to be a 400. At the time I bought it I never rode it due to no tax and mot but it started nice and looked tidy, took it for mot other day and I noticed straight away it felt like a crf450 and not the stonking...

hello! I have done a full rebuild of my Husaberg fe 400 2000. I have changed all the bearings in the cases, and made sure that the bearings where seated all the way in. I double checked the manual regarding washers and gears on the shafts so that I had it correct. The manual says that all 3...

hello again. My flywheel snapped during removal. problem is that I cant find a new one. will other husaberg flywheels fit? for example fe 450 2009? I guess as long as the crank is the same size and the ignition the same it would work?

hello! I checked the cams when i bought the bike, i could not find any signs of wear. aproximately 1000km afterwards i discovered small shiny chunks of metal in the oil screen. Turns out that cam follower bearing is chewed away along with the camshaft on the exhaust side. Unknown when camshaft...

I need help! I have a FE400 2002 bike and it has done the stator. Can anyone tell me where I can get one without costing me the earth. When I bought this I was told you either lover or hate Husabergs! I didn't know it would be ten minutes apart!! Do love it!

hello friends im looking for some new short sexy levers for my old husaberg. its got brembo brake, i wonder if ktm levers wil fit? Does anyone know where i can find some? both for clutch and front brake. found these on ebay: Orange CNC Pivot Brake Clutch Levers for KTM 450XCR w EXC EXC R 2005...

Hey guys,im looking into buying the fe 400 2002.What do you guys think about it? Is it reliable? I will ride it in trails.Thank you for the answers :D