2007

Rekluss, Scotts steering damper and rear disc guard, BRP chain guard, 300+ hrs, all original, $3,000.00

Hi, I have 2007 FE550. When the bike drops on the ground, it does not want to start with the e-starter as if the one-way bearing does not engage. I start with the kick starter and after 15 minutes of engine operation I can easily start with e-starter. The one-way bearing is with tight spring...

Chasing front and rear hubs for an 07 fe650e, would prefer from some where Australia

Hello, I read that different tire companies have variances in tire fit. If I buy a KENDA or SHINKO dual sport set of the specific size specified by Husaberg, will the KENDA and SHINKOs fit on my 2007 FE650E? Is anybody aware if any other sizes work besides the ones listed here? SPEC says...

Hey guys! I ordered a new clutch cover from taffy a few days ago and was wondering what torque setting i should use to tighten the bolts with. Thanks.

Hello I'm trying to locate new plastics and graphics for my FE450 2007 IM also looking for a side stand and a set of nuts and bolts to replace the ones on the bike that have corroded , especially the engine mounting bolts and the ones on the handle bars.. Very grateful for any help in...

Before I start this thing up and go for a break in run on my fresh rebuild. I'd like to know what the rev limiter is set at, so I can try to avoid hitting it. I can't find a single mention of it in the manual, and can't find any info online about it either.

Okay, I am not a lazy *** done my homework, that is downloaded all the manuals that I could find here or elsewhere on the Internet (not many floating around though for my Husaberg FE 450 E 2007!) but still couldn't work out exactly the quantity of oil I need to get for a change? I am assuming...

Hi guys I have a FE 550 2007, the previous owner exclusively ran it on belray thumper 15-50W here in hot Australia. Will this Castrol Activ 4T be fine? Belray Thumper is ridiculously expensive at $25 a litre and I feel as though I need a little more than a litre as I change my oil filter...

Ok, I bought this bike for quite cheap last year. It still ran, but was loud. Main bearing on flywheel side had gave up, which also made the piston eat the liner. The conrod, appears to be fine, and I feel comfortable putting it back together. My question is, the crank... I finally...

Hey guys. Just want to confirm before I pull the trigger on a supermoto setup. Your help appreciated! Cheers, -Paul

Hello everyone im Wes and a newbe Im in the process of buying my first Berg,ive had multiple ktms over the Years but this is the first Berg, its a 2007 FE650 4500km 80 hours bike looks in Good shape, i believe the crank bearings is the week point so i have read and the cranks apparently...

Hi all Back in July 2015 I had some work done to my newly acquired FE450E .. Starter motor repair kit was fitted as were new carb parts including tuning kit plus other work to the top end of the motor including cam chain, valves, dual valve springs and clutch parts and some other parts too...

I have been unable to sell bike so parting it out if get interest. Make me offers. It complete ready to ride right now so it's all there. Txt me is best. 605-3802423

I am currently sourcing aftermarket gauges to put on my 2007 FE550E. I have searched the site, and the internet, but have not found definitive answers to these questions: 1) Does the ignition have a rev limiter? 2) If yes, to what RPM is the engine limited? 3) If no, to what RPM should...

I hope this worked

Does anyone know the bearing and cone numbers for the triple clamps I want to go to my local bearing store and pick some up Thanks Frank

Hi all, The front wheel bearing housings are worn on my recently purchased FE450 the old bearings literally fell out when the wheel was removed ! New bearings have been fitted but there is still excessive play in the hubs... Im considering buying a new excel talon rim and hub or a...

Hey does the side cover have to come off to replace these 2 seals? Which would entail water pump and kick starter mechanism being disassembled? Cheers mike

($4100) I am selling my 2007 Husaberg FE 550. It is located in SLC, UT. I bought it about 3 years ago but we are moving now and it must go : This bike has a ton of power and very light. Parts can be ordered from any KTM dealer or cyclebuys.com It is currently plated with Idaho plates...