starter

ok the 24v system flat out works.i have converted my 02 650 to 24v.its the way to go starts up so easy cold or hot.i know.the starter does not like 24v.it did not like 12v either never did start.now it starts up just fine.i have started it well over 100 times. ok maybe 80 times. anyway i have...

hi all im removing all my electric starter....all the gears in the engine and the starter motor as it has not been wired for years so was wondering if any one new were in the uk i could get a bung that fills the hole were the starter motor was and how much they cost

I bought a '03 wiring, want to fit it to '02 engine, stator and ignition coil seem to fit, but the bike has that regulator which is year 2002, having the wires BROWN and YELLOW coming out. I couldn't figure out do I need a original rectifier with those contact units coming out and would fit...

Well I picked up a 99 fx501 recently. Trying to start it is a *****. When you click the start button you just get a lot of clanking. I just want to know what I should look at. Id guess starter gear maybe?

Hi all, I have a 550fe 2008 model, After a new battery and plug i am still having probs... it will start initially on the kick(sometimes that takes an age) but it used to start on the button when warm. Now its being a bit of a pain, it just clicks on the ele start without turning over, i...

Does anyone know how big is the original starter motor in a 650? I would need to know the power of the motor or how much current does it take.

Hello guys having a issue with my starter it will crank the motor one or two turns then it just spins freely. I have already tried to jump the starter direct to the battery same out come. What I'm looking for is a new starter and if they cross reference to anything ktm because I can usually get...

So, is it possible to install electric starter to FC model? What would i need(basically)? - Motor - Spacers for mounting - Few gears - battery - Starter switch? Expensive operation??

The kick start lever on my Hussy 470 will not stay tucked in. It does return when kicked, so the issue is in the lever's knuckle area....usually this is a probelm in a spring ball system but the part fiche for Husaberg and KTM does not shown these small parts and repair by replacement is...

Ok, tried the other 570 starting issues treads, but did'nt find any like my prob. The case is: When pressing the starter button, the starter tryes to make the engine roll, maks about 1 turn, and stops, the battery Volt drops from 13V to 4-5V.. Thougth that maby my battery was dead, so tested...

the one I have now sounds like it's spinning backwards and I can't find parts anywhere else

Hey guys , I have a 2010 FE 570 and it starts fine until bike gets hot, then will not turn over at all , until 10 minutes and then cools down , i had even put a new battery in and did not help :roll: :roll: :roll:

Funny one this fuse keeps blowing but not when you hit the starter it will start the bike grand but when go for a bit of a spin the next time i go to use it the fuse is blown stick new fuse in and it works alway but will be blown then after another spin you can ride for 5 mins and it might be...

i have this 96 fe600 and have tried all i can to stop an oil leak from the o-ring around the starter motor. oil pores out when i rev the bike. i have replace the oring tried 3bond, silicon gasket etc and it still leaks. i love this bike and it runs great except for the fact i have to top it up...

The Battery is new and fully charged. When I pull the starter and jump it it turns but not as fast as I would have thought. Turning by hand the starter has a lot of drag. Any ideas? Thanks. Donald

I have 2008 450 FE and seems like every time I go riding I end up having to kick start it (which is a problem all to itself). I feel that the stator is not charging the battery as I ride. Is there a technique to using the electric starter that I am not aware of other than having the bike in...

Hey all, I am looking for a little guidance. This is on my 07 450. It is a factory bike so it could differ a little. After removing my starter and the gears inside the primary area I have a knock when it runs. It runs fine, doesn't vibrate or anything. When I was pulling the sprag gear I pulled...

I recently bought a 2005 FS650C with low hours. The bike started to make some abnormal sound from the transfer case area. I decided to investigate the noise. I took the left side clutch covers off and found the nut on the primary gear was loose. I put some locktight on the threads and tighten it...

Would the proper way to update the starter on a 01 650 be, get an 08 650 starter part#82040001000 and I think I may need the starter bracket #82040002000 also? Any info would be appreciated! :?:

Its looking like i am needing to upgrade my starter motor to an R6 starter motor. Does anyone know what year(s) R6 starter motors will work for a 2004 Fe 650? thanks a bunch!