sprocket

My first Husaberg, 2011 FE 390, came with 52 tooth rear sprocket. Not sure if its just me but seemed second gear lacked a little zip right off the bottom in the slow going stuff. Should I add 1 tooth to the rear sprocket, make it a 53 tooth or would I even notice this ? Also my front...

I can't seem to find a a 53T steel sprocket, anyone know who makes one? I had an aluminum Pro Taper sprocket and it held up pretty well but have always used steel for maximum longevity. FWIW, when browsing the internet catalogs I usually use a 450 XC-W as "machine" becuase very few have Husaberg...

Anyone know which way the bolt undose always had a circlip on other bikes.

hi, got a front sprocket from a ktm 250 exc 2006 to fit my burg, as i thought they was the same, but the bugger was different..... the output shaft must be diferent.... does any one no wot ktm sprockets fit a 03 berg cheers

will a 16 tooth front sprocket fit on a 2008 550? the reason i ask is because i'm doing a lot of highway driving and i just changed my rear sprocket from a 40 tooth to an original force parts Husaberg 48 tooth rear sprocket and i lost 15km top end where, before, i cruised back and forth to work...

Hi I'm restoring my 98 Fe600E, and would like to change the timing sprocket (alum.) to a steel one. And I want to have a 04+ autodecomp. Are the steel ones of the same dimension of the 98 ones ? what year ? Thanks ZAGA

I received and installed my 47t Kush sprocket. Looking at it initially I was concerned about the inner hub and the outer tooth ring integrity, but after closer examination I see how it's made and it should be no problem. It will supposedly take about 650 ft/lbs of torque so it should be fine...

Does anyone Know If a 03 ktm 525 exc rea sprocet is the same for a 2010 450 fe? Im going to be parting out the EXC so I want to keep whats useful to me :cheers:

HI ALL LOOKING FOR SOME INFO,I HAVE A 05 FS 650 BEEN LOOKING AT DOING AWAY WITH THE PLASTIC FRAME GUARD ON THE FRONT SPROCKET AND GETTING A ALU ONE,IS THERE ANYONE DOING AT CASE SAVER OR A HYD CLUTCH SAVER IN THE EVENT OF THE CHAIN GOING ,CHEERS MIKE

Are the 07 KTM RFS countershaft sprockets enterchangeable with my 07 FE? Thanks, Dan

I was doing come trail riding yesterday amy rear sprocket split in half taking a chunk of the hub with it. Everything was tight, the aluminum sprocket just failed under the load. I think I'll go steel on my next sprocket. saving a little weight just cost me $500!

I have just orderred a 12 tooth front sprocket for my FE390; can someone confirm that: - it is 'turn clockwise' or 'anti-clockwise' to get the original one off, and, - what torque do I tighten the new one up to in Nm; do I use loctite? (my other bike a Husky 610 sprocket is held on with only a...

Hello all FOR SALE These parts are from my 2010 FE 570 with 18 miles on it. Rear sprocket 52 tooth Retail $59.99 shipped to your door for $45.00 DID chain Retail $ 106.99 shipped to your door for $85.00 Parts come from Flagstaff AZ, Pay Pal ok, [email protected] Thanks Sethro

can anyone advise me on the chain and sprocket replacement for a husa fe550 2004 I ride enduros. do i really need O,Z or X ring? or a lighter motocross type? what type of chain (or spec) should be on a fe550? 520?

Just replaced the rear sprocket and bolts on my 05. The sprocket bolts were Moose. I was not too impressed with their quality. On some of the bolts the allen wrench would not fit quite square causing the wrench to slip when torquing them down. The nuts were just O.K. On such a critical area...

so this is probably a stupid question but i got to ask. I just got a 2007 husaberg fe550e. It's my first husaberg and i love it. now to my issue i thought i was hearing some chain noise like maybe it was too loose i checked it and the adjustment is right, but the front/counter sprocket seems to...

What will fit my 08. KTM stuff. I have the stock new 48tooth I'd like to use to save a buck. I'm thinking 13/48. I'm running 14/50 now. I know I'll get hit with "13 tooth will wear out your chain slider" BS so save it. I've done it. Chain sliders are cheap and 125cc class bikes come with...

Hello, I purchased a 1994 501E Husaberg from a friend of mine and I was checking the valve lash and one of the feelers slid down the camshaft tunnel. After pulling valve cover and the clutch cover off I found it. While inspecting the internals I noticed the wear on the alloy camshaft sprocket...

Which way does the bolt turn?? It is really on there tight. Not surprising, but after turning it a bit it is still very tight. When I encounter this I always wonder whether I am loosening it or tightening it. I know that some drive nut/bolts on various mechanical machinery has left handed...

Hey All, Will the Husky 2 stroke counter sprockets fit the 07's? Do the newer 2T Husky's work? Thanks!