springs

i've had a couple lately, GGRs had one this week, daleo has had it....the conicals do like to break now and again! i wish they weren't even IN the flaming engine. so do you think with these regular breaks its a red alert? i've noticed that if this happens in the old 470s its a major...

I just swapped my 04 Supermoto suspension for some bits of an American model FE450. However, the rear spring had been changed to a "Supermoto"-spring. that is on an Enduro-damper. How do I indentify the rear spring, is there a table or a chart somewhere? More importantly, would a claimed...

I have one that just broke on my FS650e and am needing a set asap (before weekend) If anybody can forward me a website or number to call I would greatly appreciate it.

Hi all, On the older progressive sprung bergs (02s, 03s etc) what front springs are a good match for a PDS7 rear spring- I imagine a set of .46s would be the go? I currently run my 300 t 2 stroke as a PDS7/.44 combo which makes for a nice balanced bike- but unsure how the different shock...

I have an 05 650 and I am lookig to put some stiffer clutch springs in because I am frying my clutch too often due to running nitrous in hillclimb competitions. I have also heard that you might be able to add an extra steel plate to the clutch to stiffen it. Suggestions would be greatly...

Hi husaberg fans Has anyone replaced conical valve springs to regular valve springs. Regular springs are for titan valves FC 450. Does it fit also steel valve. Is the characteristc of conical & regular valve the same Conical ones tend to break and make a mess Thanks it anyone can give some...

that commentaries on the progressive springs for enduro high montain Husab 550 07

Hey guys check out this link, its all about stiffening your rear shock spring for your weight, it sounds awhole lot cheaper than the 150+ bucks to buy a new one, and it doesn't seem too hard either. Has anyone tried this? http://www.off-road.com/dirtbike/tech/2002spring/

hi, for my 02 fe650e i need stiffier/new springs for the forks and shock. i am about 250lbs, with gear on, and ride the desert but also technical. i cant find a calculator to help determine the proper springs i should use. got any links? any past experience? any stronger springs for sale...

I am trying to locate firmer fork springs for my WP 5060 forks. I have a line on some .50 rate springs with 44.6mm od x 460mm length. Will these fit? Does anyone here have the physical dimensions of the stock springs? Thank you, Paolo

$70.00 shipped out

Carrying on from my post and information receivedHERE and with the benefit of the WP spring chart found on this site: ... it appears I need the 97-250 spring (part number 9121.0008) for my 97kgs of mass. I presume that the weight's they're suggesting are net of gear because at a rough...

any of you big fellers already shell out for stiffer springs for your 06 and still have the stock 44's around? i'd like to go a little stiffer for the dez, and if i can, i'd just as soon buy someone else's springs.

I am 200 lbs and the manual recommends to change the spings to 4.8 in front and 84/250 in the back which I did. I have been following the recomedation on the clicks but im lost.... :shock: after a few stops in my setting up ride I ended up with more Qustions than answers. it seems that...

Hallo, I'm new in the forum and I really appreciate the good wave of you all! (sorry my english :oops: ) I have a question, I'm a happy owner of a 2004 650 Berg sm, last week something happen, the engine stop and when check I saw the exhaustvalve spring broken in two! Now, I found in the...

The 80/250 was a little soft so I went to a #7 progressive on my 05, do you guys think it would be better to go woth a 84/250? Thanks

:D My 2003 FE 400 came with 13/48 gears. I am a big guy, 275 lbs, I now learn that the factory springs are set for guys of 185lbs, more or less. Springs: I am going to replace the rear spring with a new KTM spring (ps-4?) and then see how the front springs feel. Gears: I was also...

Hi, When do you need to replace the valve springs?

Hi, Last week when I visited my Husaberg dealer there were three -04 650 Supermotard bikes with broken valve springs. They crack in the lower part but luckily, for these guys, the valve didn't damaged the cylinder. Seems to be a design or quality problem...

Dale, A valve spring on my 2000 FE501E broke at 347.4 hours total time, should I be concerned about using new stock Husaberg springs in the rebuild (I am using your GRIND # 792 CAM)? Do you recommend a different gentler spring? Joe