shock

Anyone know if a 2000fe 501 shock will fit a 96 fe 600.#2 Does anyone have or know anywhere to buy new or used shocks. Thanks.

I have a FE650E 2004 which was converted into Supermoto and I want to have the FS rear shock absorber. My bike has less than 10 hours of street use. My rear shock is in perfect condition. If anyone is interested in trading or selling please email me at [email protected]. Thanks!

Has anyone got a cleaver way of accessing the rebound adjuster on the shock? My last 3 rides have been in pouring rain, slop and mud. I'm getting to where I am fairly comfortable at adjusting the fork compression by feel, rather than lying on my back visually observing the screw roatating, but...

It appears that the rear shock is leaking on my 06 fe450e. There is oil weapage on the piston shaft and built up grease and grime where the piston enters the shock body(bike gets washed every ride....wet summer). Is it a do it yourself project(appears not). Any suggestions?? thank you.

Hi peeps, Having a bit of bother removing the base/bottom from my 5018pds (04 fe450e) to replace the spring with a heavier one. I've consulted the parts manual,page 25 shows an exploded view of the lower section, However, exploding it in real life is giving me grief. Q1. Does the "contra...

I am trying to remove the shock but I was wondering what the best method was to remove the bottom bolt, knowing that you have to work inside of the swingarm and that you run the risk of losing a nut inside... An Allen key on one side, a 17mm socket on the other, ok, I can loosen the bolt but...

Can a KTM PDS upper fit on a Husaberg lower shock? Yes, with some minor modifications. I went this route to try the larger reservior. It's much better. This upper body is from a 2004 KTM. You can go to my web site to see more Husaberg.US under Suspension>KTM PDS

the PDS rear shock doc we're all able to download has a few basic items missing. can anyone help? the exploded view on P2 has no index. our parts manuals are barely the same. on page 34 we're told to get a separate manual to work on the DCC nut. the dual compression set-up. the...

i'm looking to purchase the following items used from europe/UK: 1) any of these springs PDS2-250 7.5 - 9.7 = 8.6 average PDS3-250 8.0- 10.3 = 9.15 average PDS7-265 7.6 - 9.5 = 8.55 average PDS8-265 8.1 - 9.95 = 9 average anyone...

Where can I find a listing of ALL the fork (make and size) that are used on bergs since 2000? For example, 02 FC470 uses WP 48U Fork and WP 50 Shock. What about the other bikes? There must a reference chart somewhere. Thanks

Here is a side by side comparsion shock needle 2005. The telescoping is from Race Tech Inc. I will do a test project on the 'telescoping needle' and latter post the results on my web site, under 'Suspension'.

Why are the rear shocks on the KTM and Husaberg set at different angles and what effect does is it have on the PDS system? Which one is preferred? Just curious :idea: mkall32 2001 Fe 501e

Like the title says, I've never understood what the nitrogen does in my shock. Can anyone please tell me? To be precise, it there something horrible that can happen when replacing your nitrogen with oxygen? Having trouble finding refill establishments. I've filled my PDS shock with oxygen as a...

What are the procedures to bleed air from a PDS rear shock using the 'hydraulic pump motor'? 1. Where to connect the pump discharge hose, on the rebound hole or the high/low speed hole (I have the adapters)? 2. Others air bleeding procedures that must follow... Thanks. :o

Can anyone provide me with a link to the PDS shock manuals and valving charts. I am specifically looking at upgrading the valving in my 1999 FE 600 E PDS to a later model. Any link to how the PDS works as well as manuals would be helpful. What I have found so far makes me think that the...

I am looking for a shop to revalve my rear wp shock. I ****'s Racing a good shop to send it to? mars

hi everybody need a little help. when removing the rear shock from my 02 fc 550 is their anything else other than the top bolt and the one inside the swinging arm hold the unit on (is their a sleeve going thru the bottom link in the swinging arm) thanks mark.

I have an 03' Fe 400e. I weigh about 174lbs (not counting ride gear). I have the softest spring I could get on the shock and I have set both slow and fast dampening settings to the lowest setting. The rebound is set in about the middle. I have set the sag. The bike is brand new and only has...

Has anybody changed the rear shock of their FE501-94,95 to a shorter unit for supermoto racing. It seems like the rear end needs to be dropped several inches to make it turn better. I am interested to know if a shock from another bike will bolt right on.

Hi all, I have a problem finding the part called: heim joint KGW 1525 HD Has somebody changed this and especially, does it match with the KTM's part with number 50180005, called: heim joint, bearing, bushing and whatever... Thanks in advance! :(