setting

Hi all Going to adjust the valves for the first time and need a few tips, as well as the clearance? Thanks in advance. Mike.

Hi all. New here so be nice. Just bought a 2012 fe570 and I'm getting the springs upgraded to suit my weight this week. I've come off a Rmz450 and have no idea where to start with this machine. Ie no linkage. Just looking for some magic numbers to get me started.

With a progressive spring, do you set sag the same as always? Sag is sag, right? Just got my suspension back and had to put in a lot of preload to get the race sag right; now bike sag is 1/2 inch. That means the spring is too soft. But, when setting sag, I'm in the soft part, so that makes...

07 FE450 I am having issues getting my bike running after fiddling w/ the carb. It starts on choke and I can even adjust the idle very low, but when I take the choke off I can barely get it to run. I can get it to start if I give it a few throttle twists before hitting the starter. It will...

Hi can anyone tell me the valve clearance on a fe400e 2003 burg?

HELLO, I live in Brazil and recently bought a TE HUSABERG 390 2011 enhancement and also the user setting tool, used to make adjustments in injection machine. I downloaded the software from the site of Husaberg and what is happening is that the accessory is not recognizing the motorcycle. Anyone...

Hey all, I'm setting up my FE570 for SM and am trying to find out how much to lower the shock. Front is KTM SMR forks 280mm of travel with a length of 861mm from bottom of shaft to top of cap. Stock FE is 891mm same measurement. Rear is a spare FE570 shock I'm going to shorten to match the...

i just got my ecu back from being unlocked for the ust and holy crap the instructions for the using of the user setting tool suck...the manual tells you haw to change different aspects of the fuel curve etc but not how the changes affect the bike...i have an 2011 fs 570, and was wondering if...

my ktm dealer ordered me the husaberg setting tool, the part number on husabergs website ends in 140 the one my dealer sold me ends in 040 and will not communicate with the ecu and my bike. who has successfully adjusted the fuel curve on their fs 570 with the user setting tool. what pn do you...

I am curious about the standard setting on the handlebar clamp on the US version of FE 570 -09, is it in the front or the rear position. The EU version is in the rear position. Cheers Jorgen

I have been tinkering with the timing this afternoon. With the timing light and at idle the timing was about an 1/8 inch above the mark. I removed the flywheel and moved the stator about 1/8 and the timing light now shows it hiting the mark. The problem is that the idle is a bit erratic and the...

Hi Guys, I'm going to set the valves on my new-to-me 2008 FE 450. I've done BMW adjustor type valves but never a dirt bike with a decompression lever. Do I disconnect the spring or lever prior to checking and adjusting exhaust valves? Then when valves set ok reconnect and adjust cable free...

Hello friends. I am in my second Husaberg 09 450 which I love them. I think I finally got the basic click settings for me. The only thing I can´t figure out what´s best is the fork preload since I´ve tried different settings and I can´t figure out what´s best. My basic understanding is that...

Trying to set the float level on my Dellorto, from what I have read the metal should be parallel to the gasket surface.Is this when the needle is seated? What is the tab you see in the picture with the red arrow is this suppose to be making contact with the needle? This is how I found the tab...

I HAVE ALL THE SOFTWARE ON MY PC TO USE THE TOOL BUT WHEN I PLUG IT IN THE BIKE IT DOES NOT RECOGNISE THE ECU CAN SOMEBODY PLEASE HELP ME WITH THE INITIAL FIRST TIME ON BIKE SET UP,THE BIKE HAS NOT YET BEEN RUN, DO I NEED TO RUN IT BEFORE THE UST IS USED.

I Have the tool can someone give me a lowdown on were tro start with it,ie, what to do first,i have all the drivers in place on my pc ,do i need to run bike with tool attached to make any changes,when i plug the toolin it says no connection,i can only assume that the bike is not connected,any...

I have a 1997 FE 400 Elduro. Sparks just did a fine job of rewinding the stator, and I want to be sure that the timing is correct. The manual says only to release the three stator screws slightly, turn the stator to 33 degrees BTDC, and retighten the screws. Fine, but how do I know when...

When I received my NEW 2008 FE450 the displayed wheel size (on the computer upon start-up sequence) is not correct. The manual tells me what it should be, but does not tell me how to change it.... Anyone figured out how to set the wheel size into the computer? My dealer does not know...

Hi Guy, Help needed. I have just put some 17in wheels into my Berg, down from 21in and i have heard there is a way to reset the speedo for these new size wheels. The beast threw me off the beginning of the year, And i wont be able to ride Enduro for another 4 months, So this is the only way to...

i've got a 2008 fe550e but it's now set up for supermoto. how do i change my wheel size on the odometer from 2205 (21inch) to 17 inch. i've read through the 2008's owner's manual but it does not mention how to change wheel circumference from 21 inch to 17 inch??? thanks, frank