setting

Hi all I'm on a 2010 fx450 that I've picked up and just serviced the shock.Im now just setting it all up I've put in a lowering kit in the shock but is there a way to set the sag without removing, the shock to adjust,I've had a reasonable look and can't seem to find a easy access so any ideas...

If anyone has one laying around that isn´t being used, I have a friend who runs a Husqy dealership and he´s looking for one. They are discontinued so he can´t get a hold of a new one. Let me know if you are willing to sell. Thanks!

newcomer Hello there! Long story short! I was looking for some Husaberg closed cartridge setting lists but I couldn't find them here (or anywhere else on the internet). So decided to ask my Husqy dealer and he gave them to me but then I thought that other people might need them so I...

Hi! someone know the original internal calibration (shim set) of the FC 550 2005 rear shock absorber?

Hi, last year I bought a 2011 570 FE. It's a european model. I'm living in Germany and recently tried to renew the license for driving on public roads. However I failed the CO test: the Berg is homologated with a CO of 0,3 but my Berg put out 1,8 CO without catalysator and air intake reduction...

Wondering what the correct setting on the external rocker arm is supposed to be. There's some black wear on the nut underneath where it sits, suggesting that it was supposed to be touching / resting on it. At present, I've disconnected it (up at the lever end) until I figure this out. So at...

Hi guys I have a 2002 fe501 and was wondering if any1 has the torque settings for the clutch basket bolts ? Thx

Hi The rear shock on my Berg is way too firm, I'm 80kg. Going to play with the rebound and comp but would like to know how many clicks should it be in stock form and work from there. Riding is more dual sport type terrain so not too hectic.

Hi all just setting my carb back to std the clip says put on no 3 is that from top or bottom of the needle as there are 5 places to put it thanks all

So I understand you can buy a handlebar mounted switch that lets you toggle between SOFT-MID-HARD ignition maps. Is there a way to change these withou the fancy switch? And how do I determine what setting my bike is in now, how did it come from the factory? I really don't need to toggle...

Good morning ladies and gentleman. I need your help with setting my rear damper. I have to replace new damper, cause my own need a renovation. How can I work with it, to be more soft? Its realy hard, and i think it would be realy uncomfortable to ride. I have 85kg spring, and original Ohlins...

Hi all, following on from my previous thread about the snapped tappet. I have now got two new exhaust valves, new stem seals, water pump seals and other bits, the valves are lapped in and head is back on. All seems to be in order. Now I am trying to get the cams and crank timed up. I...

Hi i own a husaberg 570 FE 2012 i was experiencing alot of flame outs and under power issues long story short it turns out the tps was out of adjustment using a multimeter i checked what it was set at it read .408v in the closed throttle position so i done alot of digging around to find...

I put my bike up on the stand found my zero mark with my sag gage. dropped it down sat on it in my normal position, fully geared up. I am only seeing about 60 mm of sag. I spin the adjuster up a lot of turns to get me around my 110 mm sag mark. when i put the bike back up on the stand i can grab...

Im trying to get the fork oil level and procedure for my 11' FS570 front forks. they are a WP-USD Ø 48 mm Closed Cartridqe. I had to replace the cap on one side so I'm not sure what to do to make sure I have it setup right I tried getting the manual from my dealer but they only have it on...

hi im after some advice i have a husaberg fe650 supermoto 2003 and i need to adjust my rear shock never touched a rear shock before what i have found is my rear wheel is touching the exhaust from time to time must be when its wheeling so i need to firm it up abit ,i have already tightened the...

So I finally got this damn thing to work! Only had to take the bike back to dealership making a nice 500km road trip and leave the bike there for 3 days, to get some sort of activation code from KTM so they could flash the UST mapping in the ECU...bla bla blaa. Anyways I yesterday started to...

On a 2010 FE450 - I had my rear shock and front forks lowered 1.5 inches. I'm vertically challenged witrh a 30 inch inseam and in very tight technical terrain the stock bike was way too tall! The rear shock was re-valved when the lowering was done, but they asked me to try using the stock...

Anyone know when you can download the official "Front fork setting list" and "Shock setting list" for 'bergs? I've managed to blag a couple of photo copies from the dealer, but they do not specifically say they are for my 2011 FE570. The ones I have are article numbers 14457K02 (fork) and...

I am not too tall, 6-2 with a 34/35 inseam I am having an issue with my toes hanging lower than the brake pedal when I am sitting up in the seat. So far I have installed the Husaberg tall seat and adjusted the rear brake push rod to lower the pedal as far as it could go. I still need to lower...