problem

The problem I have been having is that my blinkers are starting to work only when they want to. Sometimes its the left side, then the right. Sometimes both and other times they both work fine. All the wiring seems fine. I did it myself last year and they had no problems till recently. First...

Hi there, I have a problem with my '08 FE550. Basically to give you a bit of background on it- My last enduro at Manby at one particular section of the track my club laid it out far too close to a water hole. Riders kept knocking the tape down as they rode past and I didn't see it as I...

so i got ready for a ride , warmed the bike up on the stand and coolant started coming out from the overflow. bout 3 hours later after trying different thing found that thermostat is stuffed. anyone else had this problem??? whats the point of having the thermostat on the bike anyway??? has...

hi , in a short , i ordered a 5 inch rear rim for my 2008fs 650e from my husaberg dealer , and he send a rim from a fs650c model. it does not fim due to the fact that the model fs650e uses a hub with dumbing rubbers but the fs-c uses the enduro style hub. the orientation of the holes for the...

Hello I had to buy a new inner clutch hub to my 04 so I looked in the manual and it says 590.32.002.200. When I ordered from my dealer he said that it was replaced with 590.32.002.500 which is from a 2007. When I replaced the part the clutch didn't work, it only "slides". So I took it...

just had a fantastic day on my berg when i encountered a problem with the starting of the bike it was just turning over when i noticed a fuel leak from the right hand side from the fuel lines fuel was under extreme pressure and squeezing by the clip so i un done the fuel filler cap and the...

Having recently fitted a 39mm FCR MK1 it ran a bit off at low speeds so I've had the carb off to change some jets thus.. 162 MJ DMS needle, clip 3 38 PJ PAS 3/8 out PS 1½ out 200 MAJ Took the APJ rod out so no squirt for tests (haven’t found the right widget to limit squirt)...

I’m having problem with User Setting Tool. It cannot connect to the ECU. The software is connecting to the UST adapter, and the status of the software is “Waiting for Commandâ€Â

I got the 501 motor running pretty good at the start but it was a ***** to kick start so i changed the flywheel and stator and it was working excellent. One kick on cold machine was enough. One day i lost the headers on the exhaust and i drowe it home Was a 5 min drive Now its like i can...

i am not very up on husabergs...i have a 03 501fe...is the ignition timing adjustable on this bike...if so what is the correct timing for this....i downloaded the manual but the photos are blurry..or maybe a quick rundown would help more...thanx

hi i have e problem with my husaberg 2004 fe 450. if its cold the motor, the starter turn the motor fast end run easy , but if it warm the starter turn the motor difficult what is the problem? thanks

Hi all, sorry for a further thread to this theme, but maybe you can help me quick. (link to fitting threads maybe) A Fe600 1999 has a engine rebuild in 2005 by a husaberg garage. The mechanican maked a test drive round his garage, all seemed ok. one month later he got a new cdi with new...

Hi All I need some help, I have bought a 2002 501 fe, and it wont start on the electric start, hot or cold. It cranks the engine over once or twice and then the starter motor kicks out an spins on its own, I have put a jump pack on it to see if its the battery, but it still does the same...

I am scheduled to pickup a new 570 Burg tuesday, now that I hear about the timing chain adjuster problem I am wondering if I should bail on the deal. During the summer I will be living about 300 miles from the nearest Burg dealer, and I sure don't want to spend my whole summer taking the Burg...

hi everybody, i m a new owner of 04' berg the first owner toked of the battery and the starter and told me that the bike won't start with it.. i 'v been asking people how to solve this problem and everybody said that all the modes' l before 2005 have problem whit starters even the dealer...

Yep Im a plonker, it seems that when I put the seat back on my 09 570 I must have trapped the seat release pull under the seat, now I cannot get to it to release the seat. Anyone got any idea how I might manage to free the seat, I cannot get to the toggle at all, its well and truly jammed...