head

Hello Husaberg community! My name is Tristan and I am from Washington State, USA. I have a 2003 FE501 that I bought a little over a year ago with ~50 hours on the clock. I put about 10 hours on the bike and it ran decently, but while jetting/tuning the carb I was doing repeated WOT runs and she...

Still looking for a cylinder head for a FE 550 Husaberg . Anyone have one ? Thanks

I am looking for a cylinder head for an 08 fe 550 husaberg . A bare head without valves would be fine

Any of you had any luck replacing valve seals without pulling the head to compress the spring? Needing to do them on both our bikes. Mine (the wife) 09 Fe450, & his 16 Fe501s (husky). Basically looking to see if anyone has had success with the "on bike" spring compressors. If so, which 1's.

I'm looking for a cylinder head for a 2008 fe 550 .

Hi all, I am not a dedicated dirt bike driver but dedicated to the Swedish made Husaberg bikes. I live just by the three different Husaberg factories in Sweden and therefore try to renovate three Husaberg bikes two which allready are in close to mint condition that will soon be mint, one...

Just thought I'd write this journey for anyone with a 17mm axle LC4 Front wheel doing a conversion to 20mm and hopefully this will prevent a few trial and error bits along the way. To convert the 17mm front wheel it is intensive but this is what I've learnt... The speedo side bearing is (from...

Per Thumper Racing on KTMTalk, the 12-15 450SXF head bolts up to the 530 and provides decent gains, plus more cam options. I imagine I'll need to modify it for the oil drain similar to using a 530 head on a 70 degree bike. Has anyone here done this? Is it worth it? I'd like a few more...

Hi guys my I need a new cylinder for my 1998 husaberg fe 501, I try to find one online and nothing if someone can tell me where to look it will be really aprreciate

Hello to all! Again, I ask for help. Whether prompt there are differences in a head of a tselindra and a valve of a cover of model 400 from 501 motors till 1999. and whether it is possible to put the head from 501 to 400.

Guys, are the copper head gaskets all they are cranked up to be? I have a 610 which is weeping coolant after 2 hrs. Composite with a spray sealer more reliable? Al.

Hi guys im loking for cylinder head and cylinder for my husaberg fe 450 09, if had it someone or knew where i should buy it for max 1000$ whit piston includet. Tanks!!!

Hi, Working on a little modification - and am trying to ascertain the inner diameter of the steering tube. My ID caliper arms can't clear the flared steering bearing races to effectively measure against the INNER walls of the head tube. Since the OD is 56mm, and I'm guessing a wall...

Hey guys I have done all the research for installing a new headlight I purchased. The light only has a negative and a positive lead on it, I used a test light on the stock headlight 3 prong connector and do not have any power to it. Does the bike have to be running in order to get voltage to...

Hello, Since I now have a 08 KTM 505 XC-F to ride I am looking into sending my 08 fe650 head to Thumper Racing to have them do their head mods, most likely Trail Port. Jesse of Thumper Racing was recommended to me by hillclimb champion (Ret.) Robie Peterson. Has anyone used them or can...

G'day guys, Can the head be removed from the 450 70* bikes with the engine still in the frame? I have a head gasket to replace. Is the any issue with cam timing with enough head surfacing to bump up the compression a little? I have a track day in two weeks. Normally if I had the time...

i have a 1997 fe501e with a head gasket leak. I found water in the oil and changed the head gasket and now have antifreeze coming out of the head gasket. How do I check to see if the head cylinder is flat and if it's not flat what should i do to fix the leak?

I bought a 1997 Fe 501 e Husaberg that has brown oil indicating a head gasket leak so I replaced it with a new one and after I got it tightened down and put back together I noticed it was leaking to the outside again. ahh annoying! What should I do? buy a new gasket and try again? The only thing...

Hi again! So after a little ride out today I found out that the head gasket is actually knackered. It started to smoke from around the head which smelt quite sweet so I assume that was the coolant and there's also oil seeping from the seal which was a give away. I am new to this so please...

hi i bought i 2002 fx 470 that had a timing chain jump bottom end seems all good can t say that about the head cap has a lovely bite mark through, i can get a 1997 400 cap just trying to work out what elses will also fit , and thanks in advance for some help guys